Oakton pH BNC 10 Operating Manual

Operating Manual
pHTestr BNC 10 Testers
®
Thank you for purchasing an Oakton pHTestr
®
Please carefully read this operating manual before using the
product to obtain an accurate and reliable test result and avoid
unnecessary damage to the tester or sensor/probe.
Features
• Large easy-to-read LCD with 3-color backlight
• Accuracy of ±0.01 pH ± 1 digit
• 1, 2, or 3 calibration points
• Auto buffer recognition: US or NIST
• Stability and battery status icons
• Auto power-off function conserves battery life
• IP67 waterproof rating
Keypad Functions
Short press = <2 seconds Long press = >2 seconds
1. When meter is turned off, short press to turn on the
meter and long press to enter parameter setting mode.
2. In measurement mode, long press to turn off the
meter and short press to turn on/off the back light.
3. In manual temperature adjustment mode, short press to
scroll up the digit one by one and long press to scroll
rapidly.
4. In parameter setting mode, short press to scroll up the
digit one by one and long press to scroll rapidly (Only in
parameter setting P2 and P3).
1. In measurement mode, short press to switch
parameter from pH to mV. Long press to enter manual
temperature adjustment.
2. In manual temperature adjustment mode, short press
to return to measurement mode.
3. In calibration mode, short press to confirm calibration
and return to measurement mode.
4. In parameter setting mode, short press to confirm
parameter and long press to enter measurement mode.
1. In measurement mode, long press to enter calibration
mode.
2. In manual temperature adjustment mode, short press
to scroll down the digit one by one and long press to
scroll raplidly.
3. In calibration mode, short press to cancel calibration
and return to measurement mode.
4. In parameter setting mode, short press to scroll down
the digit one by one and long press to scroll rapidly
(Only in parameter setting P2 and P3).
5. When the measured value is locked (HOLD icon), short
press to unlock.
pH Calibration
1. Short press
2. Connect the pH electrode with the BNC connector, rinse the
probe in distilled water and use tissue paper to gentlydab off
excess water.
3. Pour certain amount (about half volume of the calibration bottles)
of pH 7.00 pH and pH 4.00 buffer solutions in the corresponding
Pocket pH Tester.
®
calibration bottles.
4. Long press CAL/▽ key to enter calibration mode, short press CAL/▽
key to cancel calibration and return to measurement mode.
5. Dip the probe in pH 7.00 buffer solution,
stir gently, and allow it to stand still in the
buffer solution until a stable reading is
reached. When measurement stability
icon (  ) appears and remains on the
screen (see Fig 1); then short press
MODE/ key to complete the one-point
calibration. The tester returns to
measurement mode and indication icon
"M" will appear at the bottom left of the
screen, indicating the middle point of
calibration has been completed.
6. For 2-point calibration, start with pH 7.00 buffer solution; once
confirmed then rinse the probe in distilled water and dry it with
tissue paper. Dip the probe into pH 4.00 buffer solution, follow the
steps above to complete 2-point calibration. Indication icons "L"
and "M" will appear on the bottom left of the screen.
7. If necessary to perform a 3-point calibration, rinse probe with
water, dip the probe into pH 10.01 buffer solution (sold
separately), and follow the steps above. Indication icons "L", "M",
and "H" will appear on the bottom left of the screen.
Notes
A. Tester can perform 1 to 3 points automatic calibration. Please
note that pH 7.00 (USA Standard) or pH 6.86 buffer solution
(NIST Standard) must be used to conduct 1st point calibration.
Then use other buffer solution to conduct 2nd or 3rd point
calibration. Tester will automatically recognize five kinds of pH
buffer solutions. For details, please refer to the following table:
Calibration USA series
1-point 7.00 pH
7.00 pH,
4.00 pH or
1.68 pH
2-point
7.00 pH,
10.01 pH or
12.45 pH
7.00 pH,
4.00 or
3-point 1.68 pH,
10.01 or
12.45 pH
/△ key to turn on.
Indication
NIST series Recommended
icons
M
6.86 pH Accuracy:≥0.1 pH
6.86 pH,
L M
4.01 pH or Range:<7.00 pH
1.68 pH
6.86 pH,
9.18 pH or M H Range:<7.00 pH
12.45 pH
6.86 pH,
4.01 or
Range:
1.68 pH, L M H
0 to 14.00 pH
9.18 or
12.45 pH
B. The tester has self-diagnostic functions:
Self-diagnostic
Symbol Checking and how to fix
information
1. Check whether pH buffer solution
is correct (1st point calibration
Wrong pH buffer
must be 7.00).
solution or the range
2. Check whether the probe is
of calibrationsolution
damaged.
exceeds standard.
3. Check if there is any air bubble in
the glass bulb sensor.
Press CAL/ key
Wait for the measurement
when reading is not
stability icon (  ) to appear and
stable during
stay, then press CAL/ key.
measurement.
* The 1st point calibration must be 7.00 pH. Perform the 2nd point
calibration (4.00 pH) immediately after the 1st point. Do NOT turn
off the meter before you conduct 2nd point calibration. If the meter
is turned off after 1st point calibration, user will need to restart the
calibration process with the 7.00 pH first and the 4.00 pH following
after. Calibrating directly in pH 4.00 after turning meter off and
back on will cause "Er1".
pH Measurement
1. Short press /MEAS key to turn on the tester.
2. Connect the pH electrode with the tester. Rinse the probe in
distilled water, and gently dab off excess water with tissue paper
(do not rub or wipe the glass sensor).
3. Dip the probe in sample solution, stir gently, and allow it to stand
until a stable reading is reached. Take readings after stability
indicator icon (  ) appears and stays on the screen.
Special Notes
• The pH probe must be rinsed thoroughly after each use. Soap
water should be used to clean off any grease or other
contaminants.
• Refer to your pH electrode manual for important information
regarding electrode maintenance.
• Do NOT store probe in distilled or deionized purified water
because that will cause permanent damage to the pH probe.
Purified water is only recommended for rinsing the probe. The
probe should be stored in 3M KCL pH electrode storage solution
(SKU 00653-04) for best accuracy.
Setting the Parameters
When tester is turned off, long press /△ key to enter parameter
setting. Short press /△ or CAL/ key to switch from P1 to
▽
P2...P7. Short press MODE/ key and parameter will flash, then
short press /△ or CAL/▽ key to choose desired parameter,
press MODE/ key to confirm. Long press MODE/ to confirm
and return to measurement mode. In P2 or P3, short press
CAL/▽ to change the digit one by one and long press to change
rapidly.
/ or
△