Advertisement
Quick Links
Instructions for
KD Lounger
Twin
sku# 4833-KD-T
Manufactured by:
400-B Dairy Pak Rd. • Athens, GA 30607
kdframes.com • alan@kdframes.com
(2) K-15 PROP - 15"
(2) K-22-B BACK SLAT CAP - 22"
(2) K-20-S SEAT SLAT CAP - 20"
(2) K-11-L LOUNGER SLAT CAP - 11"
(2) K-9-SL SEAT LEG - 9"
(2) K-9-LL LOUNGER LEG - 9"
(1) K-10-BL BACK LEG (Left) -10"
(1) K-10-BR BACK LEG (Right) -10"
HARDWARE
H-8
2-1/4" CLEVIS PIN
H-12
3-1/4" CLEVIS PIN
H-5
HAIR PIN
H-11
WOOD DOWEL
H-19
1 - 3/4" WOOD SCREW
PARTS
(2) K-37-B BACK SLAT - 37"
(2) K-37-S SEAT SLAT - 37"
(2) K-37-L LOUNGER SLAT - 37"
(8) K-33-M MIDDLE SLAT - 33"
(1) K-29-P PROP CONNECTOR - 29"
(1) K-23-LC LEG CONNECTOR - 23"
(2) K-37-S SEAT RAIL - 37"
(2) K-31-B BACK RAIL - 31"
(2) K-24-L LOUNGER RAIL - 24"
1
Push Wood Dowels (H-11)
all the way into holes as
4
4
8
32
20
K-9-LL LOUNGER LEG (2)
K-24-L LOUNGER RAIL (2)
K-31-B BACK RAIL (2)
2
Press the Prop Connector (K-29-P)
onto the wood dowels on the
Props (K-15) and attach with
(2) Wood Screws (H-19).
shown.
K-15 PROP (2)
K-37-S SEAT RAIL (2)
H-19
K-29-P
K-15
Advertisement
Related Manuals for kd frames KD Lounger Twin
Summary of Contents for kd frames KD Lounger Twin
- Page 1 Instructions for HARDWARE Push Wood Dowels (H-11) KD Lounger all the way into holes as shown. 2-1/4” CLEVIS PIN Twin H-12 3-1/4” CLEVIS PIN sku# 4833-KD-T HAIR PIN Manufactured by: H-11 WOOD DOWEL H-19 1 - 3/4” WOOD SCREW K-15 PROP (2) K-9-LL LOUNGER LEG (2) 400-B Dairy Pak Rd.
- Page 2 Attach the Left Back Leg (K-10-BL) and Right Back Leg (K-10-BR) Be sure that the Prop to the outside of the Back Rails Connector goes below using (2) 3-1/4” Cevis Pins (H-12). the Back Rails. Do not put on the Hair Pins at this time. H-12 K-10-BR K-31-B...
- Page 3 Attach the Seat Legs (K-9-SL) and the Lounger Rails (K-24-L) K-22-B to the Seat Rails using (2) 3-1/4” Clevis Pins (H-12). Using (3) Middle Slats (K-33-M) Secure the Clevis Pins with Hair Pins (H-5). push the Wood Dowels into the edge holes on (2) Back Slat Caps (K-22-B).
- Page 4 Operation: Push the Slat Decks down onto H-19 the Wood Dowels and attach with Wood Screws (H-19). Bed position: Note: The base may need to be shifted to get the dowels to align with the holes. Lounger position with Lift up Back and swing footrest flat: down Prop onto notches on Seat Rail.