Advertisement
Quick Links
Congratulations for your excellent choice on our new electric tool which is
compliance with the best and reliable standards,ensuring you efficiency and
safety for a long period of time
Input
Rated
Method of
Specification
volt
use
power
(v)
(W)
Single-hook
PA200
110/220
510
Double-hook
Single-hook
PA300
110/220
650
Double-hook
Single-hook
PA400
110/220
850
Double-hook
Single-hook
PA500
110/220
1050
Double-hook
Single-hook
PA600
110/220
1200
Double-hook
Single-hook
P800
110/220
1450
Double-hook
Single-hook
PA1000
110/220
1600
Double-hook
Single-hook
PA1200
110/220
1800
Double-hook
Lifting
Lifting
Quan
Rate lifting
Size
speed
height
tity
Weight(KG)
(cm)
(m/min)
(m)
(PCS)
100
10
12
1
38*15*24
200
5
6
150
10
12
1
38*15*24
300
5
6
200
10
12
1
44*15*25
400
5
6
250
10
12
1
44*15*25
500
5
6
300
10
12
1
44*15*25
600
5
6
400
10
12
1
44*15*25
800
5
6
500
10
12
1
53*24*35
1000
5
6
600
10
12
1
53*24*35
1200
5
6
GENERAL SAFETY RULES
WARNING! Before using this electric tool. Carefully read the general safety rules
listed below.
1. Your sockets must comply with safety rules. In case your sockets are not
GW./NW.
suitable, it should be checked by a skilled electrician.
(KG)
2. Your sockets plug must absolutely be grounded and your electric system must
be supplied with a magneto cut out safety.
10/9.5
--When the machine is running unattended, be careful that children cannot reach
it.
--Do not pull the electric cable to disconnect the plug.
11/10
--The machine shall be protected from frost and low temperatures.
3. In case the machine cannot hoist a load,do not keep pressing the hoisting
Push button, this means that the load exceeds the machine maximum capacity.
15/14
--The machine shall not be disassembled when running or connected to power.
--Do not stand under hoisted weights.
4. Before starting the work, make sure that the steel cable is correctly winded
15.5/14.5
around the reel and the pitch is equal to the cable diameter.
5. Observe the maximum load indicated on the hoist.not that no the hook!
6. Leave at least three tums of cable around the reel,so that the cable connection
16/15
is not under stress.
--To avoid any danger, do not wind more than 15 m of cable around the reel
7. In case the steel cable is worn,it must be replaced only with a cable of
17/16
same features manufactured by us. If can be found at all authorized service
shops.
8. In case the hoist stops during the lowering of a load,it is normal that the load
28/27
goes down a few centimeters more because of inertia.
9. Attention! The hoist electric motor isn't equip with any overload cut-out(to
30/29
avoid an unexpected and unwanted restart)therefore,if you are unable to hoist a
load do not insist and let the motor cool down.
Advertisement
Summary of Contents for Dawson PA200
- Page 1 (m/min) (PCS) 2. Your sockets plug must absolutely be grounded and your electric system must be supplied with a magneto cut out safety. Single-hook PA200 110/220 38*15*24 10/9.5 --When the machine is running unattended, be careful that children cannot reach...
- Page 2 MAINTENACE MICRO ELECTRIC ROPE HOIST INSTRUCTIONS -- Periodically check that the steel cable is in good conditions. 1. Check that the screws securing the brackets and reduction gear are well tightened. 2. Check the conditions and tightening of the nuts securing the steel cable clamp.