Farpointe Data P-300-OSDP Quick Start Manual

QUICK START GUIDE
125-kHz PROXIMITY CARD READERS
WITH OSDP SUPPORT
This Quick Start Guide is intended for experienced installing technicians. It is a basic reference to ensure all connections are properly made.
Models include P-300-OSDP, P-500-OSDP, P-530-OSDP, P-620-OSDP, P-640-OSDP, P-710-OSDP, P-900-OSDP, P-403-OSDP, P-405-OSDP,
P-410-OSDP, P-453-OSDP, P-455-OSDP, as well as variants supporting most industry leading card and tag technologies. For additional
information please reference Farpointe Data's website, www.farpointedata.com.
1.0 Introduction
A key component of a physical security electronic access control
system, a proximity card reader is based on RFID technology. In
operation it is capable of reading data stored on a proximity credential
via radio frequency and without physical contact, and then passing the
data obtained to the physical access control system. Access control
systems typically manage and record the movement of individuals
through a protected area, such as a locked door.
2.0 Mounting Provisions
Each reader may be installed either indoors or outdoors. Mounting
options shown in the table below. Use supplied #6 mounting screws, or
equivalent security screws, for installation. P-400 Series readers are
supplied with #6 tamperproof screws. P-900 also comes with #10
screws for mounting on parking bollards and non-metallic flat surfaces.
Single-
Gang
Mullion Wall
Models Mount Mount*
•
P-300-OSDP
•
P-403-OSDP
P-405-OSDP
P-410-OSDP
•
P-453-OSDP
P-455-OSDP
P-500-OSDP
P-530-OSDP
•
P-620-OSDP
P-640-OSDP
P-710-OSDP
P-900-OSDP
*Plastic or metal
3.0 Cable Requirements
Cable, 4 conductor, 22 or 24 AWG [65 mm or 51 mm] twisted pair,
over-all shield and UL approved (Belden 8273, or equivalent).
Maximum bus length: 4,000 ft – 24 AWG (1,219 m)
Maximum distance between: 1,640 ft – 24 AWG (500 m)
Double- European/
Gang Parking
Wall Bollard
Mount* X-Mount*
•
•
•
•
•
•
• • •
4.0 Reader Wiring
Twisted Pair
Pair 1
Pair 2
5.0 Output Formats
The SIA standard OSDP protocol is supported for clear and secure
channel communication.
Default Address: 0
Default Baud rate: 9600bps (bits per second)
Default Secure Channel Key:
SCBK_D = 0x303132333435363738393A3B3C3D3E3F.
Asian
OSDP Protocol Technical Support:
Wall
SIA OSDP Application Profile: Basic Reader (OSDP v2.2 and higher)
Mount*
6.0 Grounding
Shield (drain) continuity must run from the reader to the access panel.
Shield (drain) and reader ground must be tied together at the access
panel and connect to an earth ground at one point.
7.0 Power
Reader may be powered by the access panel. A linear power supply is
recommended for best operation.
•
8.0 Voltage
5 to 16 VDC. 12 VDC at the reader is recommended for best operation.
Model
P-300-OSDP
P-403-OSDP
P-405-OSDP
P-410-OSDP
P-453-OSDP
P-455-OSDP
P-500-OSDP
P-530-OSDP
P-620-OSDP
P-640-OSDP
P-710-OSDP
P-900-OSDP
OSDP
Conductor Function
Red DC (5-16 VDC)
Black Ground
Green RS-485 Tx+
White RS-485 Tx-
Current Draw
30 - 75 mA
30 - 75 mA
30 - 75 mA
35 - 75 mA
30 - 75 mA
30 - 75 mA
35 - 75 mA
30 - 75 mA
70 - 110 mA
70 - 110 mA
215 - 600 mA
290 - 500 mA