FeiYu Tech Hornet-OSD Manual

Guilin Feiyu Electronic Technology Co., Ltd.
Hornet-OSD Manual
Feiyu Tech
Dear customers:
Hello! Thank you for purchasing the OSD of Guilin Feiyu Electronic Technology Co,
Ltd. In order to achieve full potential and safe operation of this product, please carefully
read this manual prior to installation.
Preface
The Hornet-OSD overlays flight telemetry information onto your video image. The
telemetry information displayed includes flight altitude, flight speed, flight direction, and
home direction and so on. You also can save the telemetry information to a MICRO SD
card (you should buy the card by yourself, for we don't offer it, picture is shown as below
then realizing trace playback via FYGCS. The Hornet-OSD can be connected to the
FY-21AP, FY-31APand FY-3ZT systems to display autopilot telemetric data, or to a GPS
receiver to display positioning data.
Hornet-OSD automatically adapts to either PAL or NTSC video input and confirms if
there is a MICRO SD card or not. The adaptive processes are within about 20 seconds.
Working status explanation:
After connecting the power supply, the indicator LED light will be activated. The
Hornet- OSD will automatically detect the incoming video (NTSC or PAL).The "NTSC" or
"PAL" will overlaid on the screen when the video signal is detected. If Data is received
from the autopilot (FY-21AP, FY31AP, FY-3ZT or GPS module) the LED indicator of
Hornet- OSD will begin to flash. If not, the Hornet-OSD will automatically restart after
waiting for 20 seconds.
Once the input video is detected even if there is interruption to the video signal, the
telemetry data of the Hornet- OSD will continue to be transmitted via the video stream.
Video in
Video out
SW
Data in
Interface Schematic Diagram:
GND VCC① Video IN
GND VCC① Video Out
① 1. DANGER: The three "VCC" ports (positive) for
inter- connected. Therefore you are allowed to connect ONE input voltage only. DO NOT
input more than one power supply or damage to the OSD will occur.
2. It is recommended to power the OSD independently to ensure a clean video display.
3. Note that power to the OSD is not supplied by the Autopilot module. Power is via the 12 volt
input.
List of Interfaces
PORT
Video in Camera or video input port
Video out OSD Overlaid video output, connect to video transmitter or video screen
SW RC receiver switch input to control OSD display
Power OSD video overlay board and camera and video transmitter power supply.
Data in FY-21AP/FY-31AP/FY-3ZT/GPS data interface
Current Sensor Current sensor input for measuring the battery voltage and current.
Detailed description of the "Video in" port
GND Connect to the camera GND
Connect to camera's power supply "VCC".
VCC (Note: Power is supplied from the OSD to the Camera. Do not input any other
power supply through this port or damage will occur).
Video IN Video input (Connect to the camera video signal output).
Detailed description of the "Video out" port
GND Connect to video transmitter GND
Connect to video transmitter power supply input "VCC".
VCC (Note: Power is supplied from the OSD to the video transmitter. Do not input
any other power supply through this port or damage will occur).
Video Out Video output (connect to video transmitter video input).
Guilin Feiyu Electronic Technology Co., Ltd.
MICRO SD card
Power
Current Sensor
GND VCC① ENG GND +5V CUR AD ENG VCC
GND PWM GND +3.3 Data TX Data RX
Video In, Video Out and Power In are all
Connection Description
http://www.feiyudz.cn
Detailed description of the "SW" port
GND Connect to the power "GND" port of the RC receiver.
Connect to the signal port of your RC receiver (you need to designate to a free
PWM IN
channel).
Detailed description of the "Power" port
GND Connected to the power "GND" that supply to the OSD control board.
Connect to the power "VCC" that supply to the OSD control board(Safe input
range:
VCC Note: this power supply is sent directly to your Video Camera and Video
Transmitter. E.g. if you are using a 12 volt Video Camera and Transmitter, the
input voltage should also be 12 volt.
Detailed description of the "Data in" port
GND FY-21AP /FY-31AP GND ,or the GND of the GPS
),
Use only to supply power to the FY-GPS module.
+3.3V
(DO NOT
Connect to the "RX1" data output port of the FY-21AP/ FY-31AP /FY-3ZT, or
Data TX
the "RX" port of the GPS module.
Connect to the "TX1" data output port of the FY-21AP/ FY-31AP /FY-3ZT, or
Data RX
the "TX" port of the GPS module.
Detailed description of the "Current Sensor" port
ENG VCC
CUR AD
+5V
ENG GND
Current Sensor：
Output to ECS Positive
Output to ECS Negative
Red
White
Yellow
Black
Application diagram
The Hornet-OSD can directly connect to the data output port of FY-21AP, FY-31AP or
FY-3ZT, or separately connect to the output port of GPS module, and then overlay the flight
data information to the video signal. The application diagram is shown as bellow.
Note：The modules in the imaginary line frame means that you can choose any one of these
modules to connect.
Introduction for the flight State of FY-21AP /FY-31AP or FY-3ZT
Name Introduction
RC Manual Flight. Autopilot deactivated.
ABM Auto balance mode
FAF For FY-21AP:Fixed Altitude flying mode; for FY-3ZT/FY-31AP:Air route fly mode
RTL Auto Return Mode
ACM Auto Circle Mode
http://www.feiyudz.cn
Email: service@feiyu-tech.com
DC6V to 12V)
connect this port to the FY-21AP / FY-31AP or the FY-3ZT).
Connect to battery positive (Red)
Connect to the current sensor output signal (White)
+5V power supplied to the current sensor from OSD (Yellow)
Connect to battery negative (Black)
Figure3. Current Sensor
Figure4. Connection Schematic Diagram
Email: service@feiyu-tech.com
Battery Positive Input
Battery Negative Input
Page 1