Gate House GCX2D01 Manual

Scan for
Installation
https://goo.gl/ENGLFG
PACKAGE CONTENTS
G
O
N
F
M
E
J
K
H
L
P
HARDWARE CONTENTS
L
M
P
SAFETY INFORMATION
Read the precautions and instructions in this manual before installing and using this lock. Save this manual for future reference.
CAUTION :
Please use four alkaline batteries (not included) for the best performance.
A. Do not attempt to disassemble any internal components of the lockset. Doing so will void the limited warranty.
B. Do not drop or hit the lockset. Too much shock may result in permanent damage.
C. Do not use pins or sharp objects to press the keypad.
D. Always create a backup of information you wish to keep (Master Code, user code, etc.) Please use the last page of this booklet as a reference.
E. Promptly change the Master Code before operating this lockset.
CARE AND MAINTENANCE
The following instructions should be followed to properly protect and maintain your lockset:
A. Remove locks, or do not install locks, prior to painting your door.
B. Periodically clean with mild soap and a soft cloth only.
C. Do not use any abrasives or chemical products containing alcohol, benzene, or acids, and avoid using sharp or abrasive objects to clean this lockset.
D. Do not allow any water or liquids into the lockset during installation.
PREPARATION
A. Before beginning installation of product, make sure all parts are present. Compare parts with package contents list and hardware contents list.
If any part is missing or damaged, do not attempt to assemble, install or operate the product.
B. Make sure backset of lock is same as backset of your door. If an adjustable latch is to be used, please adjust the backset to t your door.
C. Please read these instructions completely before attempting to install lock.
ESTIMATED ASSEMBLY TIME: 40 - 60 MINUTES
Tools Required for Assembly (not included): Phillips screwdriver
Helpful Tools (not included):
• Pencil • Hammer • Power Drill
• Chisel • Tape Measure • Flathead Screwdriver
WARNING :
If the door needs to be drilled, please be familiar with how to use a drill safely and understand all of the door preparation steps before proceeding.
DOOR PREPARATION
NOTE :
If replacing an existing lock or installing in a pre-drilled door, please skip to INSTALLATION INSTRUCTIONS.
Use TEMPLATE to measure your hole size and backset.
Cut out TEMPLATE and use to mark the door, drill holes, and chisel out the mortise.
NOTE :
Drill from both sides of the door to prevent wood splitting.
Centerline
2-1/8 in. (54 mm)
1 in. (25 mm)
Backset
TEMPLATE
NOTE: Double check your product for the correct hole sizes.
GCD-KPDDW12 Rev. 16/03-00
ELECTRONIC KEYPAD DEADBOLT
MODEL #GCX2D01
ATTACH YOUR RECEIPT HERE
Serial Number _______________
Purchase Date_______________
Questions?
Call customer service at 1-877-442-8347,
8:00 a.m. - 8:00 p.m., EST, Monday - Friday.
PART DESCRIPTION
A Exterior Assembly
B Power Strip
C Torque Blade
D Exterior Gasket
E Mounting Plate
F Interior Assembly
G Interior Cover
H Latch
I Key
J Strike Plate
K Dust Box
D
C
B
A
I
PART DESCRIPTION
O
L 3/4 in. (19 mm) Wood Screw
M 1-13/16 in. (46 mm) Mounting Bolt
N
N 13/16 in. (20 mm) Screw
O 5/16 in. (8 mm) Screw
P 2 in. (51 mm) Strike Screw
• 2-1/8 in. (54 mm) Hole Boring Bit • 2 in. (51 mm) 6d Common Nail
• 1 in. (25 mm) and 1/8 in. (3 mm) Drill Bits
Faceplate
2-1/8 in. (54 mm)
Chisel 13/64 in. (5 mm) deep.
Drill 1 in. (25 mm) hole at center of
door edge.
2 in. 1-3/4 in.
(51 mm) (45 mm)
Prepare the door jamb: Use the strike plate as a template to drill the latch and screw holes and chisel out the mortise.
The strike plate must fit flush with the surface of the door jamb.
ITEM #0788482
Door jamb hole dimension:
a. 1-3/16 in. (30 mm)
b. 1-9/16 in. (40 mm)
c. 1 in. (25 mm)
Strike slot dimension:
d. 5/32 in. (4 mm)
e. 2-3/4 in. (70 mm)
f. 1-1/8 in. (28 mm)
INSTALLATION INSTRUCTIONS
INSTALLING THE LATCH
CAUTION:
Be sure the latch cam is upright before making any backset adjustment.
QUANTITY
SKIP THIS
A. Deadbolt Latch Adjustment (
1
1
1
1 H
1
1
Turn to extend the latch bolt.
1
1
2
B. Install latch (H). Insert screws and tighten.
1
1
L
Backset
INSTALLING THE LOCK ASSEMBLIES
Thread the cable through the
hole and under the latch.
Insert the blade.
QUANTITY
2
2
1
2
2
Insert screws and tighten.
M
Hardware Used
M 1-13/16 in. (46 mm) Mounting Bolt
The cable must be arranged as shown in the diagram.
CAUTION :
Use alkaline batteries for better performance. Be sure to insert them correctly by matching the + and – polarity markings.
Do not mix old batteries and new batteries or standard (carbon-zinc) with alkaline batteries.
Outline
Install four AA alkaline batteries
(not included).
Fold here
Place on door edge
Backset 2-3/8 in. (60 mm)
1-9/16 in. 1-3/8 in.
Backset 2-3/4 in. (70 mm)
(40 mm) (35 mm)
f
K J
c
b e
a
d
NOTE: The dust box (K) is optional.
Hardware Used
2-3/8 in. (60 mm)
if your door has a backset)
a. Hold latch back and twist a. Then twist inward to x at 2-3/4 in.
outward. (70mm) backset.
b. Pull backward to the end. b. Turn back to retract the latch bolt.
Hardware Used
L 3/4 in. (19 mm) Wood Screw Qty. 2
A
E
A
The bulged part of the mounting
plate must face towards the door.
Remove the interior cover (G)
from the interior assembly (F).
G
Connect the cable rmly
into connector port.
G
F
Qty. 2 Note: The metal connector side should face outward.
Install interior assembly (F).
Insert screws and tighten.
F
O
N
G
Install interior cover (G).
Ø 2-1/8 in. (54 mm)
P
P 2 in. (51 mm) Strike Screw Qty. 2
2-3/4 should be visible.
E
B
Slide the cable through the
notch in mounting plate.
Hardware Used
O 5/16 in. (8 mm) Screw Qty. 2
N
123456
Enter default Master Code and
the lock will set up bolt direction to
complete installation.