Advertisement
Quick Links
WARNING
・DO NOT use the HURRICANE ALPHA with non-approved angle grinders. Please check against list below.
・HURRICANE ALPHA is only for grinding concrete and block. DO NOT use for grinding steel or other materials.
・HURRICANE ALPHA must be used with a vacuum designed and approved for concrete dust.
・HURRICANE ALPHA is only for use with Diamond Grinding Cup. DO NOT use with abrasive grinding wheels.
・Always check the HURRICANE ALPHA for damage, cracks, or deformation before use.
・DO NOT use the HRRICANE ALPHA if it is cracked, damaged or bent as this could lead to injury.
・Be sure to wear protective goggles, dust mask, protective gloves and foot wear, earplugs and other protective equipment when working.
・Keep the HURRICANE ALPHA away from gasoline, solvents, and paraffin.
・Ensure the work piece is securely clamped before working.
Explanation
of the pictograms.
SPECIFICATIONS
Model Code
NKC-180
Ø175～180mm (7 inch class) / h20-30mm Diamond Grinding Cup Wheel
Suitable tool
Weight
0.8kg (Main Unit with adaptor system)
Material
Concrete / Block.
Suitable
BOSCH
Angle Grinders
MAKITA
※Based on
HiKOKI (HITACHI)
2018 models.
Milwaukee
DEWALT
Metabo
FLEX
[a] Main Body / [b] Metabo Ring / [c] Adaptor / [d] Centering Holder / [e] Flange Bolt / [f] Base Flange
OVER VIEW
[g] Spacer T3.4 / [h] Spacer T6.0 / [ i ] Spacer T7.5 / [k] Spacer T9.4 / [m] Spacer T10.6
[n] Bolt (L60) / [o] Bolt (L45) / [p] Hex Wrench / [q] Hose Connector
[a]
Fig.1
PREPARATION
1.
[Metabo / Dewalt DWE4579 type]
Remove the Lever unit and O-ring
(WX22-230 and W24-230 only) , then
set [b] Mount Ring on the Gear Case.
(Fig.2)
2. Set [c] Adaptor around the Gear
Case with the Hooks securely stored
into the groove at Gear Case.
(Fig.3)
NKC-180 Dust Extractor
INSTRUCTION MANUAL
General
Read the operating
Warning.
instructions before use.
GWS20-180 / H / J / JH, GWS20-230 / H / J / JH, GWS22-180 / H / J / JH / LV, GWS22-230 / H / J / JH / LV,
GWS24-180 / H / J / JH / LV, GWS24-230 / H / J / JH / LV
GA7020 / 7040 / 7050 / 7060 / 9020 / 9030 / 9040 series.
G18 / 23 series.
AG22-180, AG22-230, AG22-230E
DWE490 / 492 / 492S / 493 / 494, D28413 / 28490 / 28492 / 28498 / DWE4559 / DWE4579 / DWE4599
(W / WE) 22-180MVT, (W / WE / WEA / WEPB / WEPBA) 24-180MVT, W26-180MVT, (W / WE) 22-230MVT,
(W / WE / WEP / WEA / WEPB / WEPBA) 24-230MVT, (W / WE / WEA / WEPBA) 26-230MVT
L21-8 180, L21-6 230, L24-6 230, L26-6 230
Metabo / Dewalt DWE4579 type
Lever unit &
O-ring
[b]
Gear Case
Fig.2
Wear
Wear
eye protection.
breathing protection.
[e]
[d]
[m]
[k]
[c]
[ i ]
[h]
[g]
[b]
[ f ]
WX22-230
W24-230
only.
Gearbox
housing
Fig.3
N300253_Rev1
Wear
Wear
ear protection.
protective gloves.
[p]
[q]
[n] [o]
[c]
Hook
Groove
-1-
Advertisement
Summary of Contents for NAKAYA HURRICANE ALPHA
- Page 1 ・DO NOT use the HURRICANE ALPHA with non-approved angle grinders. Please check against list below. ・HURRICANE ALPHA is only for grinding concrete and block. DO NOT use for grinding steel or other materials. ・HURRICANE ALPHA must be used with a vacuum designed and approved for concrete dust.
- Page 2 3. Set the position of the Hinge Pin on the center line of the angle grinder. (Fig.4 and 5) 4. Confirm the Hooks are securely located into the groove in the Gearbox housing Hinge Pin (Fig.6 and 7) Fig.4 Fig.5 Groove Hook Fig.6...
- Page 3 [ e ] [ p ] Lock Nut Wrench Diamond Grinding [ d ] [ f ] Fig.10 [g] [h] [i] [k] [m] 8. Tighten [e] Flange Bolt x 4pcs by [p] Hex Wrench. (Fig.10) 9. Remove [d] Centering Holder. 10.
- Page 4 6. Place [a] Main Body on the material and slowly move toward the grinding direction along the wall. (Fig.19) 7. Turn off the angle grinder and vacuum, then close the Front Lid. (Fig.20) Fig.19 Fig.20 Vacuum Head Office in Japan NAKAYA CO.,LTD. 1313-92 Yanagisawa, Sanjo, Niigata, Japan 27th-Nov. 2019 Eto Naoya Managing Director...