Nivetec UNICOMM SAT-504 Manual

Thank you for choosing a NIVELCO instrument.
We are sure that you will be satisfied throughout its use!
1. APPLICATION
The UNICOMM SAT-504 modem establishes communication between HART
process controller computer. The UNICOMM HART
transmitters that use standard HART
Depending on the design the following versions can be ordered:
– HART ® /USB modem, normal type;
– HART /USB modem with power supply for transmitter and switchable HART
®
– HART /USB modem with power supply for transmitter, switchable HART
®
Bluetooth interface.
®
The modem ensures galvanic isolation for the transmitter from the process controller system and it is
powered by a USB interface or a USB power bank.
2. TECHNICAL DATA
2.1 G
ENERAL DATA
Power Supply
HART current loop power supply
HART terminal resistor
Bluetooth version
Bluetooth name, Pairing code
Current consumption from USB
Power consumption from USB
Ambient temperature
Housing material
Connection to PC
Cable to PC
Connection to HART line
Ingress protection
Electrical protection
Mass
2.4 D ( )
IMENSIONS IN MM
39
3. COMMUNICATION OPTIONS
The modem meets the HART communication standards and applicable for all
®
-capable transmitters that use standard HART
HART ®
To enable communication through the USB 1.1. or USB 2.0. port of the PC a
driver program (FT 232 RL) is needed. This driver can be downloaded from the
CD-ROM containing the EView2 program package provided to all NIVELCO
transmitters purchased with HART
from the http://ftdichip.com website.
4. WIRING, OPERATION
The modem should be connected to a HART
measuring clamps. The SAT-504 does not have surge protection, thus use of an
adequate lightning protection that does not affect standard HART
transmission is advised.
UNICOMM SAT-504-2
modems are applicable for all HART
®
® communication.
2.1 A
USB interface or
USB power bank
24 V DC ±5% max. 22 mA
250 Ω switchable
2.1
SAT504-BT, 1234
<150 mA
2.2 O
<1 W
-25 C ... +55 C
(+77 F ... +131 F)
Polystyrene
USB 1.1 "B" socket
USB "A-B" 1.8 m (5.9 feet)
KLEPS2 spiral 1.1 m (3.4 feet)
IP20
Class III 1 kV galvanic isolation
0.1 kg
79
communication.
®
option. The program can also be downloaded
®
® field device by 2 pieces of KLEPS2
POWER BANK
USB / 5 V
-capable field devices and a
®
-capable
®
terminal resistor;
®
terminal resistor and
®
CCESSORIES
– User's Manual
– Warranty Card
– Declaration of Conformity
– USB "A-B" cable 1.8 m (5.9 feet)
RDER CODE
UNICOMM SAT-504-
®
HART normal type
®
HART + transmitter power
supply
®
HART + transmitter power
®
supply + Bluetooth
4.1 HART /USB
®
The clips should be positioned in accordance with polarity. When the USB cable
and the clips are connectected to the PC, the modem turns on, and switches to
the basic state marked with an asterisk (*). The following states are displayed
during operation:
Interface
® signal
USB
HART ®
HART MODEM
HART/USB BLUETOOTH MODEM
0
1
2
(
INTERFACE FUNCTION FOR ALL TYPES
(+) Red
ON
Current
HART IF.
loop
Tx/Rx
Black
(–)
LED
Name
not lit
Stby/ON yellow
* green
red
TX/RX green
* not lit
not lit
ON
* green
red
TX/RX
green
* not lit
UNICOMM SAT-504
User s manual '
: SAT-504-0, 1, 2)
Stby/ON
Tx/Rx
State
turned off (inactive mode)
turned on (standby mode)
turned on (active mode)
PC send
PC receive
no data transfer
turned off (inactive mode)
turned on (active mode)
transmission to HART ®
reception from HART ®
no data transfer