Advertisement
Quick Links
X-Pro
Speedcontroller
Dear Customer,
Thank you for your purchase of the X- Pro-Series Controller, a new generation of sensorless
speed controllers especially for 'Hacker Brushless A-Series- Motors' and other Brushless Motor
Designs. Special programming options are provided to ensure the best possible power and
performance from your motor system. 'Brushless' systems offer high power efficiency combined
with low weight and compact dimensions. For best performance and reliability from your
Controller, use only High quality connectors, motors and batteries.
Please, pay careful attention to the following instructions before you start to work with
your new motor and speed controller.
Connections:
The speed controller can be connected to the motor by direct soldering or with high quality
connectors. Always use new connectors, which should be soldered carefully to the cables and
insulated with Heat-shrink tubing. It is possible to extend the cables to the motor battery pack up
to a maximum of 8 inches. Deans Ultra or other high quality connectors are recommended for
connecting the motor battery pack to the controller.
•
Solder Controller to the Motor wires
•
Solder appropriate connectors to the Battery wires
•
Insulate all Solder connections with Heat Shrink Tubing.
•
Plug the JR connector into the receiver throttle channel.
When connecting controller to battery pack, care should be taken to ensure that multiple touches
of the connectors are not made.
Reversing the motor directions is achieved by the exchanging the position of any two wires
connected to the motor or by programming "rotation reverse".
Installing the Controller:
Install the speed controller in the model so that it is isolated from vibration and shock, using Velcro
or double sided foam tape. Allow space around it for cooling. Make sure that there is sufficient
cooling of the motor and speed controller by ducting air through adequate cooling holes from the
outside airflow. Main power packs should be connected at one attempt.
Copyright 06/07 – Hacker Motor GmbH 1
Advertisement
Related Manuals for Hacker Pro Series
Summary of Contents for Hacker Pro Series
- Page 1 Thank you for your purchase of the X- Pro-Series Controller, a new generation of sensorless speed controllers especially for ’Hacker Brushless A-Series- Motors’ and other Brushless Motor Designs. Special programming options are provided to ensure the best possible power and performance from your motor system.
- Page 2 ESC program procedure It is possible to program the ESC in two different ways: -by using a Computer with “Hacker X-Pro USB-Interface” and a special software, which can be acquired, (see then enclosed operating instructions). The USB software offers still additional adjusting parameters: -variable cutoff voltage for LiPo cells -Brake "off", "soft", "hard"...
- Page 3 -- -- -- -- -- Hard (22 ~ 30 degree) (multipole motors) --- --- --- --- --- 6. Frequency 8 kHz: (recommended) \ \ \ \ \ 16 kHz / / / / / Copyright 06/07 – Hacker Motor GmbH 3...
- Page 4 • Do not connect the motor battery to the wrong polarity; the speed controller will be severely damaged. • Controllers connected to the wrong battery polarity, WILL NOT be covered under the warranty Copyright 06/07 – Hacker Motor GmbH 4...
-
Page 5: Warranty Terms And Conditions
Warranty Terms and Conditions Hacker Brushless Motors warrants products to be free from defects at the date of purchase. This warranty does not cover any component parts damaged by use or modification. Hacker Brushless Motors reserves the right to change or modify this warranty without notice. - Page 6 The described products are in compliance with the relevant and applicable EC guidelines for electromagnetic compatibility: 89/336/EWG 92/31/EWG 93/68/EWG Many happy landings! Hacker Motor GmbH Hummler Str. 5 Tel.: 0049 (0) 8761-752 129 Fax.:0049 (0) 8761-754 314 EMAIL : info@hacker-motor.com D-85416 Niederhummel WEEE-Reg.-Nr. DE 55352581 Copyright 06/07 – Hacker Motor GmbH 6...