Advertisement
Quick Links
C1D1 Explosion Proof High Bay LED Fixture w/ Emergency Battery
This explosion proof light is designed for illumination of industrial locations. It uses the latest in
solid state lighting technology for long life, low maintenance and high efficiency.
The unique design focuses the light where it is needed, giving improved efficiency over a
conventional HID luminaire.
This light fixture is shipped preconfigured to work in the selected voltage range. This includes 100-
277V AC 50/60hz or 11-25V AC/DC depending on model selected. An internal, universal input power-
factor-corrected switch allows it to be used from any voltage within range without variation in light
output. Check product label for correct input voltage!
WARNING
To avoid the risk of fire, explosion or electric shock, this product should be installed, inspected
and maintained by a qualified electrician only, in accordance with all applicable electrical codes.
To avoid electric shock:
Be certain electrical power is OFF before and during installation and maintenance.
Luminaire must be connected to a wiring system with an equipment-grounding conductor.
To avoid explosion:
Make sure the supply voltage is within the luminaires' voltage rating.
Ensure the marked T rating is less than the ignition temperature of the Hazardous
Atmosphere.
Do not operate in ambient temperatures above those indicated on the luminaire nameplate.
Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.
For supply connections, use wire rated for at least 110°C
Recommended mounting height is 15-40 feet.
MOUNTING
The EPL-EMG-HB-50LED-RT-WLM offers a flat surface mounting system, mounted with four bolts
through the tabs on the wiring junction box. This mounting feature caters to wall mounting
preferences.
(see below wiring diagram)
WIRING
The EPL-EMG-HB-50LED-RT-WLM explosion proof wall mount LED light fixture is equipped with 10
feet of abrasion and chemical resistant 16/3 SOOW cable with flying leads. The LED light fixture
features 5 3/4" NPT threaded ports for running conduit; four of the ports are located on the corners of
the unit and the fifth port is found on the rear of the explosion proof wall mount LED fixture. Feed
wiring through a port to complete connections.
1. (See wire diagram) Wire the "Neutral", "Hot", and "Ground"
wires to power source.
2. Wire White/Red to switch if applicable.
Larson Electronics, LLC
Backup - Paint Spray Booth Approved
Instruction Manual
Phone: (800) 369-6671
WARNING: CHECK NAMEPLATE
FOR PROPER VOLTAGE. DAMAGE
FROM IMPROPER VOLTAGE WILL
VOID WARRANTY.
Fax: (903) 498-3364
EPL-EMG-HB-50LED-RT-WLM
www.larsonelectronics.com
1 of 2
Advertisement
Summary of Contents for Larson Electronics EPL-EMG-HB-50LED-RT-WLM
- Page 1 (see below wiring diagram) WIRING The EPL-EMG-HB-50LED-RT-WLM explosion proof wall mount LED light fixture is equipped with 10 feet of abrasion and chemical resistant 16/3 SOOW cable with flying leads. The LED light fixture features 5 3/4" NPT threaded ports for running conduit; four of the ports are located on the corners of the unit and the fifth port is found on the rear of the explosion proof wall mount LED fixture.
- Page 2 CHECKS TO QUALIFIED PERSONNEL !!!! THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS. SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT SALES@LARSONELECTRONICS.COM OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.
- Page 3 40°f. / 4°c. Ambient temperature (of fitting) must not drop below 40°f. / 4°c. for 72 hours. Compound must cure for 72 hours before circuits are placed into service. Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com...