Linear IEI DoorGard 212LS Series Installation & Programming Manual

Features
Simple to Install -The DoorGard 212LS Lockset installs in 15 minutes
and programs the same as all DoorGard/IEI keypads. It includes
all mounting hardware, and easily retrofits into any standard cylindrical
door prep (ANSI/BHMA A 156.2-2003). The 212LS has a replaceable
core, for the manual key override. The sleek design fits with any décor
and is available in 26D Stainless and US3 Polished Brass, right or left
handed crescent door handles.
Right Hand
212LS – C26DCR-Rt - F/G:DoorGard Grade 2 Lockset/Cylindrical,
Stainless, Crescent handle, Right handed.
212LS – CUS3CR-Rt - F/G: DoorGard Grade 2 Lockset/Cylindrical,
Stainless, Crescent handle, Right handed.
Left Hand
212LS – C26DCR-Lt - F/G: DoorGard Grade 2 Lockset Cylindrical,
Stainless, Crescent handle, Left handed.
212LS – CUS3CR-Lt - F/G: DoorGard Grade 2 Lockset Cylindrical,
Stainless, Crescent handle, Left handed.
Easy to Maintain -Change the battery in three minutes. The 212LS
Lockset uses four (4) 1.5V AA batteries for up to 15,000 uses or up to
five years. An alarm activates Low Battery Alert allowing for 30 more
uses.
User Codes - The 212LS lock recognizes up to 120 users with a
different code for each, and the lockset retains codes without batteries.
Codes can be one to six digits in length and digits can be repeated.
The Master Code is always stored in user location one (1). A reset
button is provided inside the lock which restores factory defaults and
removes codes already stored. The lockset is equipped with an override
mechanical key. The code toggles to allow passage for an event so any
key will open the lock.
Security and Protection -The 212LS Lockset is designed with a
safeguard against forced entry since the outside lever is not
mechanically connected to the latch until the lock activates. Also, after
three invalid code attempts, there is a 20 second lockout period for the
keypad.
Rugged Design -The 212LS is designed for both commercial and
industrial use.
Lockset Parts List
1. Spanner wrench 11. Interior Faceplate/Door
2. T-Strike Door Latch Handle w/battery case
2-3/8" Backset 12. Interior Faceplate
3. T-Strike Door Latch 13. Override Keys (2)
2-3/4" Backset 14. Pin Wrench (pries open key
4. Strike Plate slot cover)
5. Strike Plate Cover 15. Key Slot Cover
6. Latch/Strikeplate Screws 16. Screws: 2 sets Lock
7. Allen Wrench Assembly screws (thick,
8. Exterior Door Handle/ thin doors)
keypad 17. Sealing Washer
9. Exterior Gasket 18. Faceplate Assembly Nut
10. Interior Gasket
2 3
1
7
8
10
9
13
14
15
16 17
Figure 1. Parts Diagram
Door & Frame Prep
•
Remove existing Lock from door
•
If it is new door with no holes, use
•
Measure backset.
1. Unpack the lockset and inventory all parts. Remove mount-
ing screws, separate lock assembly, and both interior/exterior
handle plates and the two rubber gaskets.
2. Insert the strike plate hole cover (#5) and attach strike plate
(#4) in the door jam/frame, securing with two Phillips head
screws.
3. Install T-Strike Door Latch (#2 or #3) into doorjam/frame and
secure with two Phillips head screws.
4. Assemble locks inserting two Rubber Gaskets (#8, 9, 10, 11).
5. Thread battery wires through hole in Interior Faceplate/Door
Handle (#11).
4
6
6. Attach Interior Faceplate/Door Handle (#11) to Exterior Door
5
Handle (#8), securing with two short or long assembly screws.
(#16)
7. Insert batteries and connect battery clip.
12
8. Secure Interior Faceplate (#12) with clear plastic washer with
Nut (#17, 18)
9. Use spanner wrench (#1) to tighten nut (#15).
10. Program the system as described in this manual.
11
11. Instruct the users on lockset operation.
•
Use Pin Wrench (#14) to pull off cover (#15).
18
•
Use override key (#13).
•
Turn left twice.
Installation Steps
template provided
Installation
Manual Operation
P1345