Quoizel TDR8408PN Assembly Instruction Sheet

Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Bulb Recommended: (1) Medium Base bulb 100W Maximum, Alternate bulb (1) 23W CFL.
Estimated Assembly Time:
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Fixture can only be mounted in the direction indicated on page 2.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
Crossbar Assembly
A
x 1
-
STEP 1 Install Crossbar Assembly
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug.
Outlet
Box
Figure 1
-
STEP 2 Fit Backplate to
Crossbar Assembly
A. Remove mounting balls from the
Crossbar Assembly (A). Fit the
backplate on Fixture Body (B) to
the Crossbar Assembly (A) and
secure with mounting balls.
Note: The backplate on Fixture
Body (B) should be snug against
the wall and the mounting balls.
If not, adjust the length of the
nipple on the Crossbar
Assembly (A) by unscrewing the
preassembled hex nut and lock
washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
achieved. Once the backplate on Fixture Body (B) is secure, remove
the mounting ball and Fixture Body (B) and proceed to Step 3.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2014 QuoizelInc.
Assembly Instruction Sheet #IS-TDR8408
For Styles TDR8408PN and TDR8408K
20-30 minutes
Fixture Body
B
x 1
A
Outlet Box Screws
(not included)
Supply Wires
with Ground Wire
Mounting Ball
Backplate
Mounting Screw
A
Hex Nut and
Lock Washer
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
-
STEP 4 Install Fixture Body
A. Carefully tuck all wires into the
outlet box and position the
backplate of fixture body (B)
over the outlet box. Align the
holes in the backplate with the
mounting screws. Place caulk
(not supplied) into the
previously removed mounting
balls and then attach fixture
body (B) using the mounting
balls. Hand tighten until snug.
-
STEP 5 Install Bulb and
Figure 2
A. This fixture uses standard bulb with medium base. Maximum 100
watts. Insert bulb and screw snugly into place.
B. Make sure exterior wall surface and fixture backplate are free of dirt
before applying caulk. Using exterior
grade caulk, caulk over top of
B
backplate and down other side. Do
not caulk bottom of fixture
backplate to ensure proper
moisture drainage.
Your fixture is now assembled and
ready to use. Enjoy!
1of2
White wire
from fixture
Black wire
from fixture
Ground wire
from fixture
Mounting Ball
Backplate
Mounting Screw
A
Figure 4
Apply Silicone Sealer
Socket
Backplate
Figure 5 Bulb
Figure 3
B
Exterior
Grade Caulk
December2014