Download Print this page
Xylem Bell & Gossett Domestic CC Series Instruction Manual

Xylem Bell & Gossett Domestic CC Series Instruction Manual

Vented condensate units

Advertisement

Quick Links

i
Bell & Gossett
a xylem brand
®
Domestic
Vented Condensate Units
cc;
Series
SERIES CB'" with
Optional Panel & Equipment
cs·;
SERIES
CHD'; CED'"
Not Pictured
INSTALLER: PLEASE LEAVE THIS MANUAL FOR THE OWNER'S USE.
A
SAFETY
INSTRUCTIONS
This safety alert symbol will be used in this manual and on
the unit safety instruction decals to draw attention to safety
related instructions. When used, the safety alert symbol means
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT
IN A SAFETY HAZARD.
h.
This product can expose you to chemicals
.. including Lead, which is known to the State of
California to cause cancer and birth defects or
other reproductive harm. For more information
go to: www.P65Warnings.ca.gov.
EXPLOSIBLE
(2) All Units
DN0483 (Small) - DN0484 (Large)
Pump
M
M
M
cs;
cs;
SERIES CBE'" with
Optional Panel & Equipment
DO NOT PRESSURIZE TANK.
ISOLATE TANK DURING LEAK TEST.
DO NOT RESTRICT VENT.
DO NOT PLUG OVERR.OW.
OPEN IM..ET VALVES SLOWLY.
DO NOT USE AS A FLASH TANK.
FAILURE TO FOUOW
INSTRUCTIONS CO LLD RESULT
IN SERIOUS INJURY OR DEATH.
CBE,
CHD;
If the decals as noted below are missing or are illegible contact
your local B&G representative for a replacement.
1. Electrical connections to be made by qualified Electrician in
accordance with all National, State and Local codes.
2. Motor must have properly sized starter with properly sized
heaters to provide overload and undervoltage protection.
3. If pump, motor or piping are operating at extremely high or
low temperatures, guarding or insulation is required.
4. Operating personnel should be trained in the operation of
condensate return units.
PSI
IN. HG.
OWGS
POWER V,
CONTROL V.
EXPLOSIBLE
TOTAL
F.l.AMP.
ISOLATE TANK
SHORT CIRCUIT CURRENT:
DURING LEAK TEST
�� Bell & Gossett
;
(2) All Units
���1;',�
i
DN0485 (Small)
DN0016
DN0486 (Large)
INSTRUCTION MANUAL
REVISION F
M
CED
SERIES CC'" with
Optional Panel & Equipment
ACAUTION
PUMP
DO NOT RUN PUMP DRY,
SEAL DAMAGE MAY DC�.
PUMP
INSPECT PUMP SEAL
REGULARLY FOR LEAKS,
REPLACE AS REOUIRB>.
FOR WBRICATION
REOUIREMENTS, CONSULT
PH.
HZ
SERVICE INSTRUCTIONS.
FAIWRE TO FOLLOW
INSTRUCTIONS COULD
RESULT IN INJURY OR
PROPERTY DAMAGE.
"�•
kA RMS SYMMETRICAL,
P70644
V. MAXIMUM
§
All Units
';;:
a
DN0158

Advertisement

loading

Summary of Contents for Xylem Bell & Gossett Domestic CC Series

  • Page 1 Bell & Gossett INSTRUCTION MANUAL DN0158 a xylem brand REVISION F ® Domestic Pump Vented Condensate Units ™ ™ CBE, CHD; Series SERIES CB'" with Optional Panel & Equipment SERIES CC'" with SERIES CBE'" with Optional Panel & Equipment cs·;...
  • Page 2 INSTALLATION AND DESCRIPTION (Vented Condensate Units) DESCRIPTION CAUTION: NOT A CHEMICAL PUMP Pumps are float operated to return accumulated condensate to Inject boiler feed compounds from chemical feed tank a boiler feed tank. into boiler feed piping – never into condensate tank. Failure to follow these instructions could result in injury or property Receivers are non-code cast iron or steel.
  • Page 3: Operation And Maintenance

    PUTTING THE UNIT INTO SERVICE CAUTION: DO NOT REVERSE Reverse operation can cause extensive damage to Assure that the unit is piped in accordance with instructions pumps. Jog the motor to test for direction of rotation. Failure on page 2. to follow these instructions could result in injury or property WARNING: EXPLOSIBLE damage.
  • Page 5 PUMP SERVICE INSTRUCTIONS FOR 609PF CENTRIFUGAL PUMPS These close coupled vertical centrifugal pumps are equipped with mechanical seals. If system has not been properly cleaned FIG. 2 prior to installation of pump, foreign matter such as dirt, pipe 2DPF01 scale, core sand, etc. may clog the impeller and damage the seal.
  • Page 6 PUMP SERVICE INSTRUCTIONS FOR CENTRIFUGAL PUMPS (EXCEPT ‘B’ OR 609) Vertical mounting puts motor above floor dirt and water Close coupled centrifugal pumps are designed for years of trouble free service. Units have mechanical shaft seals. 1. Close inlet gate valve and operate pump momentarily to remove as much liquid as possible from pump.
  • Page 7: Hot Surfaces

    PUMP SERVICE INSTRUCTIONS FOR SERIES B35 PUMPS Close pump isolation valve or system return line valve. Operate pump momentarily to discharge as much water as possible. Close pump discharge valve. HEAVY DUTY BALL BEARING MOTOR CAUTION: HOT SURFACES Surfaces are hot when system is in operation. Do not WATER SLINGER touch hot receiver, let unit cool before servicing.
  • Page 8 24. Observe operation thru several cycles. Xylem Inc. 8200 N. Austin Avenue Morton Grove, Illinois 60053 Phone: (847) 966-3700 Fax: (847) 965-8379 www.xylem.com/bellgossett Bell & Gossett is a trademark of Xylem Inc. or one of its subsidiaries. © 2019 Xylem Inc. DN0158F June 2019...

This manual is also suitable for:

Bell & gossett domestic cs seriesBell & gossett domestic cb seriesBell & gossett domestic cbe seriesBell & gossett domestic chd seriesBell & gossett domestic ced series