Advertisement
Quick Links
WARNING
・DO NOT use the DUST TANK with the angle grinder which can NOT be fitted correctly instructed by this manual.
・DUST TANK is only for cutting concrete, block, and tile. DO NOT use for cutting steel or other materials.
・DUST TANK must be used with the Vacuum suitable for the concrete dust.
・DUST TANK is only for Diamond cutting blades. DO NOT use with abrasive wheels or tipped saw blades.
・Always check the DUST TANK for damage, cracks, or deformation before use.
・DO NOT use the DUST TANK if it is cracked, damaged or bent as this could lead to injury.
・Be sure to wear the protective goggles, dust mask, protective foot wear, earplugs and other protective equipment when working.
・Keep DUST TANK away from gasoline, solvents, and paraffin.
・Ensure the cutting material securely clamped before cutting.
Explanation
of the pictograms.
SPECIFICATIONS
Model Code
NK-230
Suitable Blade
180-230mm / T2-3mm Diamond Blades.
Cut Depth
5-60mm (230mm Blade)
Weight
2.2kg (Main Unit with adaptor system)
Concrete, Block, Tile, ...etc.
Cut material
Suitable
BOSCH
Angle Grinders
MAKITA
HiKOKI
Milwaukee
DEWALT
Metabo
FLEX
[a] Main Unit / [b] Mount Ring / [c] Adaptor / [d] Centering Holder / [e] Flange Bolt / [f] Base Flange
OVER VIEW
[g] Spacer T3.4 / [h] Spacer T6.0 / [ i ] Spacer T7.5 / [k] Spacer T9.4 / [m] Spacer T10.6
[n] Bolt (L60) / [o] Bolt (L45) / [p] Hex Wrench / [q] Swing Duct / [r] Vacuum Joint / [s] DW plate
Fig.1
PREPARATION
1.
[Metabo / Dewalt DWE4579 type]
Remove the Lever unit and O-ring
(WX22-230 and W24-230 only) , then
set [b] Mount Ring on the Gear Case.
(Fig.2)
2. Set [c] Adaptor around the Gear
Case with the Hooks securely stored
into the groove at Gear Case.
(Fig.3)
* Exchange the bottom plate of [c] into [s]
when using Dewalt DW4579 type.
NK-230 Dust Extractor
INSTRUCTION MANUAL
General
Read the operating
Warning.
instructions before use.
GWS20-230H, GWS22-230H, GWS22-230JH, GWS22-230LV, GWS24-230H, GWS24-230JH, GWS24-230BV, GWS24-230LVI,
GWS24-230JVX, GWS26-230JH, GWS26-230JBV, GWS26-230LVI
GA9020 / 9030 / 9040 series.
G23MRU, G23UBY, G23SEY, G23SCY, G23SC3, G23SR, G23SRU, G23SW2, G23SWU, G23UC, G23UCY, G23UDY
AG22-230, AG22-230E
DWE494, DWE490, DWE492, D-28490, D-28492, D-28498, DWE4559, DWE4579, DWE4599
WE24-230MVT, W22-230MVT, WE22-230MVT, W24-230MVT, W26-230MVT, WE26-230MVT, WX22-230, W24-230
L21-6 230, L24-6 230, L26-6 230
[a]
[s]
Metabo / Dewalt DWE4579 type
Remove Lever unit & O-ring.
(WX22-230 & W24-230 only)
[b]
Gear Case
Fig.2
Wear
Wear
eye protection.
breathing protection.
[e]
[d]
[m]
[k]
[c]
[ i ]
[h]
[g]
[b]
[ f ]
Exchange to [s]
(DWE4579 type only)
Gear Case
Fig.3
N300221-Rev6
Wear
Wear
ear protection.
protective gloves.
[p]
[r]
[n] [o]
[q]
Hook
[c]
Groove
-1-
Advertisement
Summary of Contents for NAKAYA DUST TANK
- Page 1 WARNING ・DO NOT use the DUST TANK with the angle grinder which can NOT be fitted correctly instructed by this manual. ・DUST TANK is only for cutting concrete, block, and tile. DO NOT use for cutting steel or other materials.
- Page 2 3. Set the position of the Hinge Pin on the center line of the angle grinder. (Fig.4 and 5) 4. Confirm the Hooks securely stored into the groove at the Gear Case. Hinge Pin (Fig.6 and 7) Fig.4 Fig.5 Groove Hook Fig.6 Fig.7...
- Page 3 8. Tighten [e] Flange Bolt x 4pcs by [p] Hex Wrench. (Fig.10) 9. Remove [d] Centering Holder. 10. Set the proper Spacer [g] / [h] / [ i ] / [k] / [m] on the spindle of the angle grinder. 11.
- Page 4 5. Pivotally lower the angle grinder slowly. (Fig.20) [CAUTION] The Plunge Dust can't be well extracted with the cutting depth over 40mm. Front Roller Fig.20 Head Office in Japan Nov-27th 2019 NAKAYA CO.,LTD. 1313-92 Yanagisawa, Sanjo, Niigata, Japan Eto Naoya Managing Director...