Advertisement
Quick Links
All
they are installed and operated properly. To fully enjoy the comfort, safety, and reliability of your
new Widespread Faucet, please follow the instructions below.
California Faucets reserves the right to make modification and specification changes at any time.
Handle
Hot
Fig. 1
***NOTE: SHUT OFF WATER SUPPLY BEFORE BEGINNING INSTALLATION***
1
Install spout according to the type of tee it has:
For spout with 4-way tee:
-Remove the Tee, Flange Nut and Stainless Steel Washer.
-Insert the spout through center hole of the sink or
countertop.
-Place Washer and Flange Nut onto Shank
from below. Align spout and tighten Flange Nut until Spout is
firmly in place.
-With O-Ring in place on end of Shank, slide Tee onto Shank.
-Place the Rubber Washer, Brass Washer and Nut
onto Nipple and tighten.
Brass Washer
Nipple
Fig. 2
NOTE: Due to sediment in the water it may
be necessary on occasion to remove the aerator
and clean the screen with a soft bristle toothbrush.
WS_ii_120917
Tel: 714-891-7797
Fax: 714-891-2478
Toll Free: 800-822-8855
WIDESPREAD FAUCETS
www.calfaucets.com
®
products are engineered to provide quality performance provided
Please visit www.calfaucets.com for most current technical data.
Set Screw
Escutcheon
Decorative
Base Ring
(1 1/8" Hole size for
drilling, recommended)
1"
1"
4-Way Tee Shown
Brass
Supplied Nut
Min. 8"
All Widespread faucets meet ASME A112.18.1-2005/CSA B125.1-05
Maximum flow rate: 1.5 gpm (5.7 L/min)
Stainless Washer
Flange Nut
Shank
O-Ring
(If necessary apply grease)
4-Way
Tee
Rubber Washer
Nut
IMPORTANT
Sink/
Countertop
Stainless Washer
Lock Nut
Cold
1/2"x3/8"x12"
Flex Line
OR
For spout with 3-way tee:
-Remove the tee, lock nut and notched washer.
-Insert the spout through center hole of the sink or
countertop.
-Slip the notched washer over spout shank. Align
notch for pop-up rod to pass through, then thread
lock nut onto the spout shank. Align spout
and tighten nut firmly.
-Place white washer into top of tee and screw
assembly onto spout shank.
-Insert lift rod through top of spout
Flow Restrictor
& Rubber Washer
(For use on model
#5302 only)
Fig. 3
Please refer to Finish Care Instructions for complete
cleaning information. Wipe frequently with a soft, damp
cloth. Never use acids, harsh abrasives or detergents
"A"
DIMENSION
"A" Dimension is from sink/countertop
"A"
to tip of stem broach
Handle
Series #
"A"
32
2 3/8"
Fiber
33
2 3/8"
Washer
34
2 3/8"
Bottom
35
2 3/8"
Nut
36
2 3/8"
38
2 5/8"
40
2 5/8"
42
2 5/8"
43
2 1/4"
44
2 7/16"
46
2 1/2"
47
2 1/2"
50
2 1/4"
51
2 1/2"
52
2 5/8"
Notched Washer
Lock Nut
Shank
Rubber Washer
3-Way
Tee
IMPORTANT CLEANING NOTICE
INSTALLATION
INSTRUCTIONS
Handle
Series #
"A"
53
2 1/4"
55
2 5/8"
57
2"
58
2 5/8"
59
2 5/8"
60
2 1/4"
61
2 1/4"
63
3"
64
2 5/8"
65
2 1/8"
66
2 1/8"
67
2 1/4"
68
2 3/8"
69
2 3/8"
.
Pg 1
Advertisement
Summary of Contents for California Faucets 32 Series
- Page 1 To fully enjoy the comfort, safety, and reliability of your new Widespread Faucet, please follow the instructions below. California Faucets reserves the right to make modification and specification changes at any time. Please visit www.calfaucets.com for most current technical data.
- Page 2 Supply Riser P-trap, angle stops, and supply risers (not supplied) are not supplied. We recommend genuine Angle Stop Cal-Trim parts available at your authorized (not supplied) California Faucets dealer. "P" Trap Fig. 8 Fig. 9 (not supplied) WS_ii_120917 Pg 2...