1. Manuals
  2. Brands
  3. Flair Electronics Manuals
  4. Medical Equipment
  5. ENS24
  6. Instruction manual

Flair Electronics ENS24 Instruction Manual

Wireless annunciator
Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
Enlarged version
Instruction Manual
W ireless Annunciator
Model ENS24 and ENS32

Table of Contents

Introduction
Features
Trouble Shooting
Introduction
Flair Wireless Annunciators come with a standard zone identification
graphic or can be made with custom graphic displays also.
This Manual describes the basic installation and operation of the Flair
Wireless Annunciator, Models ENS24 and ENS32.
Built to last the test of time by Flair.
Features
24 and 32 Zone, Standard Configuration
State of the Art Microcontroller
Highly Visible, Easy to Customize Display
Individual Zone Status LEDs
Single Touch Common Silence, Reset and Test
Easy to register multiple transmitters
One Common Open Collector Output and one common SPDT
Relay
3-19
Rev A

Advertisement

Table of Contents
loading

Summary of Contents for Flair Electronics ENS24

  • Page 1: Table Of Contents

    Flair Wireless Annunciators come with a standard zone identification graphic or can be made with custom graphic displays also. This Manual describes the basic installation and operation of the Flair Wireless Annunciator, Models ENS24 and ENS32. Built to last the test of time by Flair. Features ...

  • Page 2: General Specifications

    Paper Template Push Status LEDs (Under Cover)  ENS24 and ENS32: Surface Wall Mount, Black Plastic Enclosure, No Buttons Power Supply Sounder -A = 12 VDC Power Supply with Plug-In Transformer -AB = 12 VDC Power Supply, Plug-In Transformer and 5 Ah Back Up Battery ...

  • Page 3: Removing Front Graphic Cover And Case Lid

    Annunciator - Inside 1. Removing Front Graphic Cover and Case Lid Remove the Front Graphic Cover by grabbing the edge with your Sounder fingers and gently lifting up. The rivet will pop out of the hole Run your fingers around the cover gently pulling up the three Status LEDs Relay remaining rivets until the cover is free from the front of the...

  • Page 4: Prepare For Benchtop Setup And Testing

    3. Enrolling Transmitters 2. Prepare for Benchtop Setup and Testing Enrolling of the transmitters is done using the LCD display and 4 buttons below it to navigate the programming menu. *** It is recommended that you initially setup the annunciators and enroll all transmitters on a benchtop prior to installing in the field.
  • Page 5 You will be prompted to “RESET DEVICE”. When the transmitter has been successfully assigned to a zone the display will show “REG ZONE: ##”. The cover of the transmitter must be removed in order to access the reset switch. Press the reset on the transmitter Press “Enter”.

  • Page 6: Other Menu Options

    4. Other Menu Options: External Audible Sounder 5.3. There are several other programming functions available after entering the programming menu. More details may be found in the installation manual. 1. Deleting transmitters 2. Enrolling/Deleting Reset Transmitters – Not Recommended 3. Enrolling/Deleting Repeaters – Not Recommended 4.
  • Page 7 Silence/Reset/System Test Push Buttons Power LED 5.4. 5.5. The Annunciator has two push buttons on the upper left ON Green: During normal AC operation side so the user may silence, reset or perform a system ON Red: During DC operation, Loss of AC Power test on the Annunciator and the Control Board.

  • Page 8: Transmitter / Zone And Repeater Table

    6. Transmitter / Zone and Repeater Table Transmitter Zone Identification Number AT FLAIR WE CARE Manufacturing: Magnetic Contacts, Fence Sensors, Annunciators and Graphic Displays Since 1967 Flair Electronics 212 Mercury Circle Pomona, CA 91768 Phone (909) 568-0063 Fax (909) 568-0151 www.flairsecurity.com...

This manual is also suitable for:

Ens32

Table of Contents