Jade Safety & Security Weather Light Series Quick Manual

'' WEATHER LIGHT '' SERIES FOR NON-MAINTAINED LUMINAIRES
TECHNICAL CHARACTERISTICS GR-935
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION 3 VA
BATTERIES (Ni-Cd)
2.4V/1.5Ah
BATTERY PROTECTION
INDICATIONS - CONTROLS
CHARGING TIME
90min
MINIMUM AUTONOMOUS DURATION
FLUORESCENT LAMP
LIGHT SOURCE INTENSITY (emergency)
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
CONSTRUCTION MATERIALS
EXTERNAL DIMENSIONS
TYPICAL WEIGHT 840gr.
GUARANTEE
GENERAL
These luminaires are used in places where
emergency luminaires are needed.
Each luminaire must be permanently connected
to mains power supply.
In normal operation the battery is charging and
the 2 yellow LED's light in the screen.
In case of a mains power supply failure the
luminary will light the lamp automatically in
emergency mode. When the mains power
supply is restored the device turns to normal
operation.
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance or
testing must be done by authorized personel
only.
2. The device must be connected to the mains
power supply thru a fuse dependent by the total
amount of the line's power load.
3. It is sugested to check every month the
indication LED for battery charging, and by
pushing the TEST button (see the paragraph 8
on page 2), to check the emergency cirquit. The
lamp should light as long as the TEST button is
pressed . In the opposite condition contact the
installer.
4. It is sugested to check every 6 months the
minimum autononous duration by disconnecting
the mains power supply. Count the time that the
lamp lights and in case of less time than the
minimum autonomous duration the battery must
Page 1 of 2
GR-936 GR-937 GR-961/WP GR-962/WP
220-240V AC/50-60Hz
4 VA 5.5 VA 4 VA
2.4V/3Ah 4.8V/3Ah 4.8V/1.5Ah
From full discharge
Battery charging LED, TEST button
24h
3h 3h 90min
11W (CFL)
8W (T5) 2x8W (T5)
85lm
170lm
IP 65
EN 60598-1, EN 60598-2-22
o
0 to 40 C
Up to 95%
Bayblend FR3010, transparent polycarbonate
355 x 145 x 73 mm
900gr. 1100gr. 980gr.
3 years (1 year for the lamp and the battery)
be replaced. If the measured time is considerably
less than the minimum autonomous duration
contact the installer. In case of battery or lamp
replacement, these must be replaced by parts of
the same type .
5. It is sugested to replace the lamp every 8000
hours of continuous operation The frequent .
failures of mains power supply reduces
dramaticaly the lamp s life time ' .
6. In case of inactive use for a period greater
than 2 months, disconnect the battery by pulling
out the battery's connector.
7. I s not allowed to discard batteries in to t i
common trash bins, they must be discarded
only in battery recycling points. Do not
incinerate.
INSTALLATION
To install the luminaire follow the installation
instructions on page 2.
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
0: Non Maintained
A: Including test device
*90: 90min duration
180: 180min duration
923962001_09_019
1 Remove the diffusor and the lamp. Place simultaneously 2 flat blade screwdrivers and pull up
gently the reflector.
2 Install the included plastic cover in to the unused hole and install the base plastic (with the
included mounting screws and plugs).
3 Instal the cable gland and pass the round cable thru.
4 Place the battery's connector to the corresponding connector on the P.C.B.
5 Connect the mains as shown in figure 1.
6 Install the included tie (if needed) to fasten securely the power cables.
5.5 VA 7 Refit the reflector and fasten the two small screws (included).
4.8V/3Ah 8 Finaly place the lamp and the diffusor by using the 4 included screws (tightening torque 1.2Nm).
3h
1
N
L
1040gr.
230V AC
Figure 1
Mains connection
8
TEST procedure with extra care!!
9 Unfasten the mounting screws (step 8) and remove the diffusor. When the luminaire is supplied
by the mains, press on the marking for TEST as shown in the picture below. Mount the diffusor by
using the 4 removed screws.
Page 2 of 2
INSTALLATION INSTRUCTIONS
2 3
6
4
7
923962001_09_019