Advertisement
Quick Links
User Manual
Fast Ethernet Optical Switch
(1 Fiber Port and 4 UTP Ports)
Brief Introduction
Many thanks for purchasing our fiber optic equipment,
this fiber switch supports IEEE802.3U/100Base-Tx/Fx
protocol, as well as 10/100M auto-negotiation full
duplex and half duplex. The following purchasing guide
Advertisement
Summary of Contents for Jfopt JF954MM-2
- Page 1 User Manual Fast Ethernet Optical Switch (1 Fiber Port and 4 UTP Ports) Brief Introduction Many thanks for purchasing our fiber optic equipment, this fiber switch supports IEEE802.3U/100Base-Tx/Fx protocol, as well as 10/100M auto-negotiation full duplex and half duplex. The following purchasing guide...
-
Page 2: Packing List
Model Specification JF954MM-2 10/100M,dual fiber,multimode 2km,SC JF954SM-25 10/100M,dual fiber,single mode 25km,SC JF954SM-40 10/100M,dual fiber,single mode 40km,SC JF954SM-60 10/100M,dual fiber,single mode 60km,SC JF954SM-80 10/100M,dual fiber,single mode 80km,SC JF954SM-100 10/100M,dual fiber,single mode 100km,SC JF954SM-120 10/100M,dual fiber,single mode 100km,SC... -
Page 3: Installation
Fiber Switch 1 piece AC/DC5V1A Adapter 1 piece Copy of user manual 1 piece Installation 1. Interface RJ-45 Interface RJ-45 Connector supports CAT5 twisted-pair with typical length of 100 meters. It features the function of MDI-MDIX through parallel lines. Fiber Interface SC/ST fiber interface is of 100M full-duplex mode,dual fiber(TX and RX)should be cross-connected(TX-RX,... - Page 4 The network device(work station,hub or switch) with RJ-45 interface is connected to RJ-45 jack of optical transceiver through twisted-pair,and multimode/single mode fiber is connected to SC/ST fiber interface of the optical transceiver.Then switch on, the corresponding LED is on for correct connection.(See the table below for the LED indicator lamp) Figure 1 Schematic drawing of connection Explanation for LED indicator lamp...
- Page 5 Packet goes through TX end Link/Act Blink Power is on and normal Transmission Characteristic Optical Receiving wavelengt Distance Model Power Sensitivit (KM) (dBm) y (dBm) (nm) JF954MM-2 1310 -22~-12 ≤-30.0 ≥2 JF954SM-25 1310 -15~-8 ≤-38.0 ≥25 JF954SM-40 1310 -8~-3 ≤-38.0 ≥40 JF954SM-60 1310 -3~0 ≤-38.0...
-
Page 6: Main Features
JF954SM-80 1550 -5~0 ≤-38.0 ≥80 JF954SM-100 1550 ≥-1 ≤-38.0 ≥100 JF954SM-120 1550 ≥1 ≤-40.0 ≥120 JF954SM-25A 1310/1550 -15~-8 ≤-36.0 ≥25 JF954SM-25B 1550/1310 --8~-3 ≤-36.0 ≥25 JF954SM-40A 1310/1550 -8~-0 ≤-36.0 ≥40 JF954SM-40B 1550/1310 -8~0 ≤-36.0 ≥40 JF954SM-60A 1310/1550 -3~0 ≤-36.0 ≥60 JF954SM-60B 1550/1310 -3~0... -
Page 7: Technical Parameters
4.Automatic identification of MDI/MDI-X cross line. 5.Support max forwarding package length 1552/1536 bytes option. 6.In conformity to safety code of FCC and 15 CLASS A and CE MARK. Technical Parameters Support IEEE 802.3z/AB 100Base-T/SX/LX/ZX 1.Connector: 4 UTP RJ45 connector, 1 SC/ST/FC connector.