Advertisement
Quick Links
IWAWUAb MARINE TOILET
GFATURES
Easy t o
clean
white ceramic b owl
Sturdy wood seat
wlth
durable baked enamel flnlsh
Forward angled pump for easy operation
Canvenlent top-maunted dry bo wl selector
Reversible pump mounting for right or lelt hand installation
~
~
External seal housing/rod guide for easy replacement
Extra
larae
seal housina allows
ist ton rod assemblv to
b e removed wtthout r e r k v i n g
vilve cover
Smooth external surfaces
with skirted
base
to maintain
cleanliness
Base of pump
and valve cover
are skirted t o conceal
gasketiflap valves
Triadic full-flow joker
valve
t o avow accidental blockage
MuRFangle discharge port for versatlllty o f plumbing
connection
SPECIFICATIONS
Inlet port-
3/4",
Dlsharge port
-
1-112"
Weight
-
compact
bowl:
26
lb
large bowl: 32
ib
OPERATION
Manual Marine tolleta have tradltlonally been wmewhat c u m b
some and wnfuslng t o operate and maintain. The Jabsm toilet
has been deslgned wlth user convenience in mind. The pump
assembly la angled toward to provide a natural, smooth stroke
action. It has a top mounted weUdry bowl selector whlch can be
operated wlth thesame hand used for pumping without releasing
the pump handle.
The Jabsco toilet is surprisingiy easy to operate. Simply move the
weVdw bowl selector to the wet bowl oosition llem and Dumo handle
up and down a few times to add some water
to
t h ; bowi pridr to use.
After using, Rush by again pumping handle up and down (in wet bowl
position) until bowl is thwoughly rinsed and evacuated. Then move
the
weVdry bowl selector to
the
dry bowl position (right) and w t i n u e
pumping until only about one cup of water remains in
h
bottom of
bowl. Leave the weVdw bowl selector in the dw bowl oosition when
toilet is not in use.
APPLICATION
The Jabsco Manual toilet is designed to meet the requirements of
onboard marine applications. It may be installed above or below the
waterline. If the toilet is, or can be, below the waterline at any normal
(including static) altitude of vessel heel and/or bim, a
W4"
Vented Loop
Fitting must be installed in a length of hose that connects the Rushing
pump to the rear of the bowl. The vented L w p Fitting should be
positioned so it remains about eight inches or more above the waterline
at ail angles of heel and trim. If h e toilet is plumbed to an overboard
discharge, the discharge hose must
also
include a Vented Loop Fitting.
(See WARNING.) The toilet may be plumbed so waste is discharged to
holding tank, directly overboard (where permined by law) or into a
certified waste treatment device. For installation versatility, the pump
assembly may be positioned on the left or right hand side of the bowl.
Its multi-angle discharge
port
will allow routing of discharge hose in
almost any direction for ease of installation a i d neat appearance.
The toilet is available with either a compact china bowl to fit restrictive
areas or a large bowl with household size seat assembly for maximum
comfolt Its fornard analed double action oumo with coivenient too
mounted dry bowl selocior is easy and natlral to operate It is self:
priming with a dry suction 1 1 of up to
3
feet
( 1
metor) and a dlschaw
Models 29090-2000
291 20-2000
MODELS AVAILABLE
29090-2000
Compact Slze B o w l
P
Seat
29120-2000
Household Size B o w l
&
Seat
waterline it must be installed with properly
oops. Failure to do so can
hlch can cause loss of
Posltlonlng and Mounting
The Jabsco Manual Toilet is assembled at the factow for operation
wvth the nght hand. If preferred, or required by
available
space, h e
pump ano bowl may be rotated 180 dogmas to prov~do leh hand
operation. To do this. remove hose from inlet elbow (back of bowl1
and rorate elbow t80degrees.
It
may be necessary
remove the
elbow, loosen spud retan ng nut and rotate the spud fitting so elbow
will be tight when pointing in the o ~ ~ o s i t e
diredon. Remove. rotate
180 degrees and wlnstai both the bowl and pump assembly. Rocon-
nect hose to inlet elbow and the to;lel is ready lor loh hand operation
The toilet must be installed on a well suppatted flat surface.
Ideally, if underside of mountinu surface is accessible. the toilet
base should be through-boltedjus ng
5/16'
bolts, washerr and
locknuts) to the mounnng surface If the undnrslde of mounting
surface is not accessibli,
the use of 5/16' lag bolts and washeis is
an acceptable alternative.
Before installing, position toilet in bcation to be installed. Ensure
there 1 s adequate space around to let to easily operate pump and rase
seat and lid to a fully opened position. Seat and lid should swing open
at least 110 degrees and be supported when open to avoid strain on
hinges. Ensure the base drain plug is accsssible and inlet and
discharae hoses can be attached to their resoective oms without
lnduung s,gn~kcant lateral force The dlschaige elbow may be rotated
(by
loosening
two Range saews, rotating elbow and rehghtenlng
saews) to accept the most convenient muting of the discharge hose
When proper installation has been established mark h e four base
mountino hdes on mountino surface and remove toilet. Ensure that
no wiring or plumbing is paGtioned under the mounting surface which
may be accidentally damaged when the surface is drilled. Drill
head to 9 feet 1 3 meters). A full-flow biadic
ioker
valve resists blo&aoe
while providing positive back-flow prevention.
"
appropriate size holes for fasteners being used. Mount toilet using Rat
washers between head of bolts and plastic toilet base. If desired a
Advertisement
