Advertisement
Quick Links
INSTALLATION INSTRUCTIONS FOR INSTALLING PILLAR FACE KITS.
FOR USE wITh RAVENNA™ SERIES GAS APPLIANCES
KIT CONTENTS
Please ensure that all these parts are in one of the three boxes. The pillar
face comes packaged in three separate boxes. The following items are
included in each box:
Box 1 - Part # J7527
Cast door with barrier
Box 2 - Part # 75092
2 ea. Mounting Brackets
1 ea. Backing Plate With Cast Bottom Attached
f i r e - p a r t s . c o m
8 ea. 5/32" Allen Head Screws
3 ea. Control Knob Extensions (for units with Robertshaw valve)
1 ea. Control Knob Extension (for IPI units with SIT valve)
1 ea. Cast Top
1 ea. Left Pillar
1 ea. Right Pillar
1 ea. Instruction Sheet
Box 3 - Ornate grills (upper and lower grills) - Part # 75091
or
Traditional grills (upper and lower grills) - Part # 75094
NOTE: The brackets to attach the pillar face assembly to the appliance
are included in the second box.
Pillar Cast Face Kits*
37-5/8" w x 23-3/4" h
Model
Cat. No.
75093
PILCST-GLASS
75092
PILCST-PILRS2
75094
PILCST-GRL-TRD3
75091
PILCST-GRL-FIL3
* The pillar cast face kits also requires the use of the surround
kits listed below (sold separately - See reference information on Page
6). The surround kit must be installed prior to the installation of
the pillar cast face kit.
Cast Surround Kits
Cat. No.
Model
75156
RDV-DBV-PCFP3044-TOP,
75157
RDV-DBV-PCFP3044-SIDES
Description
Glass Door (Box 1 of 3)
Back, Pillars, Top (Box 2 of 3)
Traditional Bar Grills (Box 3 of 3) OR
Ornate Filigree Grills (Box 3 of 3)
(ref. form # 900157-00)
Description
30 x 44 Top (Box 1 of 2)
30 x 44 Sides (Box 2 of 2)
NOTE: DIAGRAMS AND ILLUSTRATIONS ARE NOT TO SCALE.
P/N 900147-00
REV. A, 01/2015
Cast Surround
Pillared Face
Shown with Traditional Bar Grills
Figure 1A
Traditional Bar Grill (75094)
Ornate Filigree Grill (75091)
Figure 1B
TOOLS NEEDED
Phillips Screwdriver
5/32" Allen Wrench or T-Handle Wrench
GENERAL INFORMATION
If you encounter any problems, need clarification of these instructions
or are not qualified to properly install this kit, contact you local distribu-
tor or dealer.
Read this instruction sheet in its entirety before beginning the installation.
ALL wARNINGS AND PRECAUTIONS IN ThE INSTALLATION AND
OPERATION MANUAL PROVIDED wITh ThE APPLIANCE APPLY TO
ThESE INSTRUCTIONS.
HEARTH PRODUCTS
KITS AND ACCESSORIES
PILLAR FACE KITS
1
Advertisement
Summary of Contents for IronStrike PILCST-PILRS2
- Page 1 Cat. No. Description 75093 PILCST-GLASS Glass Door (Box 1 of 3) Figure 1B 75092 PILCST-PILRS2 Back, Pillars, Top (Box 2 of 3) 75094 PILCST-GRL-TRD3 Traditional Bar Grills (Box 3 of 3) OR 75091 PILCST-GRL-FIL3 Ornate Filigree Grills (Box 3 of 3)
-
Page 2: Installation Instructions
TURN OFF ThE FIREPLACE AND ALLOw IT TO COMPLETELY COOL BEFORE PROCEEDING. INSTALLATION INSTRUCTIONS Step 1. Install the Cast Surround Kit (sold separately) per the instructions provided in the kit (see Page 1 for ordering information and Page 6 for reference information). Step 2. - Page 3 Step 5. Door Installation Instructions Rotate the door so the hooks on the two mounting brackets attached to the back of the door are pointing down. Each pillar has two slots (see L in Figure 5). Slide the hooks on the door brackets into the four slots (L) in the two pillars and push the M = Upper Grill door down until the hooks rest in the slots (L).
- Page 4 Step 7. Top Installation Instructions: Step 8. Face Removal: The underside of the top has a semicircular recess at both ends. To remove the face from the gas appliance, disassemble the The pillars have a corresponding semicircular protrusion. Rotate parts in the reverse order of assembly. the top as shown in Figure 7 and position the top so the recess in each end slides over the protrusions on the pillars (see P in Step 9.
- Page 5 Step 10. Extended Knob Installation Instructions: For IPI models see instructions on Page 6. When installing a cast pillar face on these appliances, use of these extended knobs are needed for ease of access to the gas controls. a) Locate the gas valve controls (see Figure 9). b) Remove the phillips screw from the pilot/on/off gas control knob as shown (see Figure 10).
-
Page 6: Reference Information
REFERENCE INFORMATION Step 11. Extended Knob Installation Instructions: Model: Ravenna™ RDV-IPI Figure 14 shows the dimensions of the cast surround kit. See order- ing information on Page 1. When installing a cast pillar on these appliances, extend the control panel forward and use the extended knob when a hi/lo valve is present. See Figure 13.