olympia electronics ZLD-28/EM Quick Start Manual

SELF-TESTING MAINTAINED EMERGENCY ILLUMINATION SIGNS WITH WHITE LEDs
TECHNICAL CHARACTERISTICS
Mains voltage
Maximum power consumption
Battery (Ni-MH)
Battery protection
Indications
Recharging time
Minimum emergency duration
Light source intensity (230V) / (emerg.)
Degrees of cover protection
Produced in accordance with
Operation temperature range
Relative humidity
Construction materials
External dimensions (LxWxH)
Typical weight
Guarantee
Thank you for purchasing this product of Olympia
Electronics. A European manufacturer.
GENERAL
These luminaires are used indoors (ta 40 C)
where emergency light is needed.
Each luminaire must be permanently connected
to mains power supply.
In normal operation the led strip lights and the
battery is charging.
In case of a mains power supply failure the
luminaire will light the led strip automatically in
emergency mode (powered by its battery). When
the mains power supply is restored the device
turns to normal operation.
Installation
To install the illumination sign you must follow
the installation instructions on pages 2,3 and 4.
Battery Cut-off
The luminaire enters in this operation when the
mains power supply fails and battery has lost its
energy. During this operation the luminaire
enters the idle state and battery consumption is
negligible, in order to be protected from deep
discharge.
Battery charging
The battery charging is completely controled. In
this case, is achieved the perfect battery
maintenance, as well as the elongation of its
duration. When the battery has completely
charged, it charges with a maintenance current.
Manual Test
The manual test can be conducted only if the
main power supply
connected.By pressing the test button briefly an
operation test is initiated. During this test period
Page 1 from 4
ZLD-28/EM
3.8W / 6.5VA
125lm / 125lm
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3, EN 1838
290x172x38mm
o
and the battery is
High Quality European based Manufacturers
ZLD-34/EM
220-240V AC/50-60Hz
4W / 6.7VA
3.6V/1.5Ah
Overcharging and full discharging protection
Charge LED, Lamp Fault LED, Fault LED
145lm / 125lm
0 to 40 C
up to 95%
Aluminum, plexiglas
350x242x38mm
760gr. 1125gr.
3 years (1 year for the battery)
all indication LEDs are OFF.
Automatic test
This test includes all the operations that provide
the manual test and is conducted automatically
every 15 days. In order to be performed, the
main power supply and the battery should be
connected.
Automatic Autonomous Test
The Automatic Autonomous Test is conducted
and measures
operation. This test is conducted automatically
every six months. In order to be performed, the
main power supply and the battery should be
connected (the battery should be charged). If
the battery is not charged, the test is postponed
until the battery is completely charged. If during
the Automatic Autonomous Test the luminaire's
duration is lower than the named, then the
battery must be replaced.
Back Up Operation
The autonomous duration of battery during
emergency mode is at least the one that is
stated in the list of the first page. During
emergency mode, a LED strip test is also
performed.
Resetting Errors
Push the Test button for 5 seconds, to
extinguish all the indicated LED errors. Then the
luminaire enters regular operation mode.
Changing the operating mode
Press and hold the TEST button for more than 5
seconds, the luminaire will erase first the errors (3
LED indicators will light in succession) and after 2
seconds the LED Lamp Fault will remain lit
steadily. When the TEST button is released, the
ZLD-44/EM
4.3W / 6.9VA
24h
3h
170lm / 125lm
IP 40
o
450x275x38mm
1565gr.
the luminaire`s
922504456_09_002
back up