InMotion in45S3 2 Series Quick Start Manual

in45S3x2x Series
tamper Resistant CCd dome Camera
Quick Start guide
Before operating this product, please read this quick-start guide to ensure proper
use. Please store these instructions a safe place for future reference.
FEAtuRES
• Polycarbonate Housing • Privacy Masking
• DC Varifocal lens • On Screen Menu
• ⅓" Sony SuperHAD II CCD • 3 Axis gimbal
• 600TVL Resolution • 12VDC/24VAC Powered (D Model)
• 0.05 Lux @ 50IRE Sensitivity • 12VDC Powered (L Model)
• Wide Extended Range
pRECAutioNS
1. Before installing and operating the unit, please read this manual carefully.
2. Precision components are contained in this camera, please avoid violent
vibrations during installation and maintenance. Do not connect the power
until you have completed the installation.
3. Please obey all local electrical wiring regulations when using or installing this
unit.
4. Do not use abrasive or corrosive materials for cleaning. Use only a soft cloth
for cleaning.
5. To prevent damage to the lens or sensor, do not point the camera directly into
the sun or very strong light sources.
6. Do not use the camera outside it's working temperature (-10°C~ 50°C / 14°F
~22°F) or humidity (<90%) ranges.
7. Ensure that the power supply meets the current requirements of the camera
and that the supply voltage is inside the tolerances of the camera model
12VDC±10% or 24VAC±10%
8. Ensure that any mounting fixings used are adequate to support the load of
camera.
9. In case of camera failure, do not attempt to dismantle or service the camera
yourself. Please refer to qualified service personnel for repair of the camera.
CoNNECtioNS/CoNtRoLS
1. In-line cable OSD joystick
2. Power Input connector. This is a 2.1mm
Coaxial jack. Observe polarity of 12VDC
connections. The polarity of 24VAC
connections is not important.
The centre conductor is +12VDC /
24VAC±10% and outer is ground. Refer to
the adjacent diagram for clarification.
3. BNC Connector. Video Output. 75Ω, 1Vp-p
RELEASiNg thE CovER
⑩

1. The rear of the dome is cover marked with a  as indicated by ① above
2. Depress the release button ② and gently lift the lid in the direction ③ until
resistance is felt.
3. Push the  on the cover in direction ④ and the front of the cover will
release from the base.
Rev0.3
4. Lift the cover off in direction ⑤
RELEASiNg thE mouNtiNg pLAtE
⑥
⑦
1. Release and remove the cover as detailed above.
2. While holding the base plate insert
the base counter clockwise ⑧, until it stops, and then pull the plate from
the base
1. N.B. When considering a mounting position, ensure the chosen location
provides open access to the release button. If the button is obstructed, it will
not be possible to open the housing for maintenance.
1. Using the enclosed drill template, mark and drill the three mounting holes for
the base. Choose an appropriate drill bit for the surface you are drilling in to
and ensure that the diameter is correct for the fixings being used.
2. Open a hole large enough to pass the power / video / and joystick through the
mounting surface.
3. Use appropriate No.8 screws (and wall plugs, if applicable) for the mounting
surface in use.
4. Ensure that the fixings can adequately bear the weight of the camera.
5. Mount the camera base plate
6. Pass the cables through the hole made in 2., align the camera base with the
plate and rotate the base clockwise until it clicks into place.
7. Make the power and video connections and set up the camera as appropriate.
8. Once commissioning is complete, replace the dome cover by aligning the 
on the cover with the release button and applying even pressure on the cover
12VDC
GND
rim ⑩ to snap it home.



⑩




⑧
BOTTOM
⑨
Base Plate
⑨ , pull lever ⑥ in direction ⑦ and turn
mouNtiNg
⑨
LENS AdjuStmENt & poSitioNiNg
⑧
⑤
②
⑦
④
①
⑥
③
①
C
The camera and integral varifocal lens are mounted on a 3 axis gimbal. To gain
access to the camera, remove the liner by gently squeezing the liner at points ①
and lifting the liner off in direction ②.
To position the camera, rotate the main gimbal in axis "A" by gripping and rotating
the gimbal arms ③, to rotate in axis "B" rotate the bars ④ on the gimbal disk, to
tilt the camera in axis "C", rotate the edge of the gimbal disk ⑤, until the desired
position is obtained
The field of view may be adjusted by loosening the zoom lever, ⑥, and moving
until the required field of view is obtained. Loosen the focus lever ⑦ and adjust
to obtain optimum focus. Remember to tighten both levers when adjustments
are complete to prevent image drift. The levers should be tensioned "finger tight"
only. Replace the liner by aligning and pressing gently in direction ⑧ until the
liner snaps back into place.
oSd ACCESS
Connect the Video-Out of the camera to a display monitor.
To activate the camera OSD, depress the joystick button on the in-line
cable joystick.
Push the joystick  to select a menu from the list.
Push the joystick   to change the selected value.
Press the joystick button to open a sub-menu or execute a command.
oSd mAiN mENu
When the OSD menu is launched, you are
presented with the adjacent opening screen.
A menu option followed by a  the presence
of a sub-menu.
An option in () indicates the feature is locked by
another setting and cannot be adjusted.
A  indicates return to previous menu.
iRiS mENu
• iRiS Adj - ELC/ALC (default). Select ALC when using a DC lens
• ALC menu:
• dC Level - sets the level of the iris when
using a DC lens.
• FLK- ON or OFF. On sets flickerless mode,
use this when flicker is observed in the
image under fluorescent lighting. When
FLK is ON, the shutter menu is disabled.
• Shutter: OFF, 1/120~1/120K. Set this
on to reduce the exposure time of each
image. This can be used to reduce blur in images with fast changing
content.
• ELC menu: Use this option for fixed or manual iris lenses
• Brightness: sets the exposure of the image.
A
B
UP
L R
DOWN
CAMERA MENU
 IRIS ALC
AGC ADJ (ON)
DAY/NIGHT AUTO
WHITE BAL ATW
DNR MIDDLE
PICTURE ADJ 
OTHER SET 
EXIT SAVE
LENS SET
 DC LEVEL
[ 8]
FLK OFF
SHUTTER OFF
 