Download Print this page

GCS ZA1501IN-5 Installation & Operation Manual

Arrival sensor

Advertisement

Quick Links

Federal Communications Commission Statement
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) This device
must accept any interference received, including interference that may cause undesired
operation.
FCC Caution
"the user that changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment."
FCC Statement in User's Manual (for calss B) FCC Section 15.105 "Federal
Communications Commission (FCC) Statement"
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Limited Warranty
GCS Guarantees that every wireless Arrival Sensor is free from physical defects in
material and workmanship under normal use for one year from the date of purchase. If
the product proves defective during this one-year warranty period, Vision will replace it
free of charge. GCS does not issue any refunds. This warranty is extended to the original
end user purchase only and is not transferable. This warranty does not apply to: (1)
damage to units caused by accident, dropping or abuse in handling, or any negligent use;
(2) units which have been subject to unauthorized repair, taken apart, or otherwise
modified; (3) units not used in accordance with instruction; (4) damages exceeding the
cost of the product; (5) transit damage, initial installation costs, removal cost, or
reinstallation cost. For information on addtional devices, please visit us at
www.gcs-st.com
ZA1501-5 V0
1080128
Installation & Operation Manual
Arrival Sensor
ZA1501IN-5
ZA1501EU-5
ZA1501RU-5
ZA1501US-5
ZA1501IL-5
ZA1501KR-5
ZA1501HK-5
ZA1501JP-5
ZA1501BR-5

Advertisement

loading

Summary of Contents for GCS ZA1501IN-5

  • Page 1 Vision will replace it ZA1501US-5 free of charge. GCS does not issue any refunds. This warranty is extended to the original ZA1501IL-5 end user purchase only and is not transferable. This warranty does not apply to: (1) damage to units caused by accident, dropping or abuse in handling, or any negligent use;...
  • Page 2 System (0x09) Heartbeat (0x05) Protocol: Z-Wave™ (ZM5101) Arrival sensor Notification Frequency Range: Type Micro USB Cable Clock (0x0B) Timer Ended (0x02) 865.22MHz (ZA1501IN-5) Operation manual 868.42MHz (ZA1501EU-5) (Table 1) 869.00MHz (ZA1501RU-5) 908.42MHz (ZA1501US-5) 916.00MHz (ZA1501IL-5) V1 Alarm: 919~923MHz (ZA1501KR-5) 919.80MHz (ZA1501HK-5)
  • Page 3 Operation 8. All the rest commands depend on Z-Wave standard Notice: If you are installing the entire Z-Wave™ system for the first time, please refer to the installation guide of Z-Wave™ Interface Controller and full charging the 9. Factory Default Reset: Long press the program switch up to 10 seconds to send the arrival sensor before using..

This manual is also suitable for:

Za1501eu-5Za1501ru-5Za1501il-5Za1501us-5Za1501kr-5Za1501hk-5 ... Show all