VDC Display Systems Marquee 8520 Ultra Quick Start

Remote Control Layout and Controls
Status Page
to display status
pages
Projector
to command a single
projector in a multi-
projector system
Display Controls
To adjust:
Color Contrast
Tint
Brightness PROJ
Detail Volume
COLOR
Enter
to select a highlighted
CONT
menu item
to select a dialog box
option
ENTER
Arrow Keys
for adjustments
for menu item selection
for movement between
edit fields
1
4
Numeric Keys
for menu item selection 7
for number entry
0
Mute
to turn audio on or off
to turn menus on or off
For Technical Assistance Please Contact:
VDCDS Technical Services: 321.784.4427 or support@vdcdisplaysystems.com
Quick Start - Marquee 8520 Ultra
Utilities Menu
To access the following utilities:
Source Setup
Remote Options
Channel List
Clock/Events
Memories Display
Service
Preferences
Picture Menu
To adjust or set:
Phase
Blanking
Size
Clamping
White Balance
Retrace
Focus
Decoder Options
Sync
*
UTIL PIC
Geometry Menu
To adjust:
Size
Bow
TINT DETAIL GEOM
Keystone
C Linearity
Side Pin
S Linearity
Top
Skew
BRITE VOL CONV Bottom
Convergence Menu
to adjust red, green and
EXIT
blue convergence
Exit
to exit from a menu or
function
Source
for input selection
for channel up/down selection
for source message display
SOURCE
Recall
to select a Recall Memory
to go back one screen during
2 3 RECALL
menu/help display
to view hidden slide bars
when message display is turned off
5 6 HELP
Help
#
8 9
for context sensitive help
for setup guides
MUTE STBY POWER
# Test Pattern
to select a test pattern
for display
Display Systems
Power
to turn the projector on or off
Standby
to turn both picture and
audio on or off
QUICK START - MARQUEE™ 8520 Two-Piece Series
This document is intended to provide the necessary information to perform the initial assembly, test and quick setup of the
Marquee™ 8520 Two-Piece Series projectors. For complete detailed assembly and operating instructions, refer to the
Marquee™ 8520 Service Manual (VDCDS P/N: 71178-02) contained on the accompanying CD-ROM.
Note: The 8520 projection system is shipped in two-
separate assemblies. Before any testing or operation
of the system can be accomplished, the Electronic
Chassis (EC) and the CRT Head Assembly (HA)
MUST be connected together. Refer to the inside
section (Figure 1 and Figure 2) DO NOT apply any
main power until both sections have been assembled
per this instruction sheet.
Step 1. Once the EC and HA have been assembled
together, connect the AC power cord,
located in the lower-left side of the EC.
Note: Input voltage must be between 90 –
264 VAC, 50/60 Hz.
Step 2. Connect an External Source (Optional)
a) Connect a 3, 4 or 5 wire source to the
projector's built-in RGB input-slot 1
(VIM). Ensure the source is on and properly connected.
Step 3. Turn the Projector On
a) Hold down the [POWER] key on the keypad for about one second to turn the projector on.
Step 4. Select Internal Test or External Source
a) Internal Test: Press [#] to display the first level test pattern. Press [EXIT] to return to the external
source if available.
b) Select the External Source: Press [SOURCE] [0] [1] to select the source connected to the Video Input
Module (RGB).
Step 5. Adjust the Display: Guided Help provides several on-line tutorials which explains how to operate the
projector and assist you during the setup process.
]
a) Press [HELP] [1 to select the Guided Source Setup tutorial.
90 - 264 VAC
50 - 60 Hz
SYNC
RED GREEN BLUE HOR/COMP VERT
BNC
connectors
RGB and Sync Signals from Source
VDCDS Doc#: 790200101 / Revision 001