Advertisement
Quick Links
SFP28 Module Installation Notes
PRODUCT NAME
GMZP088-VSL01D
GSZP318-DSL10D
This installation note provides the installation instructions for the GBICS.com SFP28 modules. These SFP28
modules are hot-swappable input/output (I/O) devices, which connect the module port with the fibre-optic or
copper network.
Ensure that you understand safe handling of lasers and have the following tools and parts available to install an
optical transceiver in a switch chassis:
•
Electrostatic discharge (ESD) grounding strap
•
A rubber safety cap for the transceiver
Ensure you understand how to prevent ESD damage.
To install an SFP28 in an uplink socket please follow the below instructions
1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to the
ESD point on the chassis.
2. Remove the SFP28 from its packaging.
3. Ensure that the SFP28 is covered by a rubber safety cap. If it is not, cover the SFP28 with a safety cap.
4. Remove the dust cover covering the port in the uplink module. Save the dust cover in case you need to
cover the port later.
5. Using both hands, carefully place the SFP28 in the empty port in the uplink module. The connectors
should face the uplink module.
Caution: Ensure the transceiver is aligned correctly when you slide it into the port; misalignment
might bend the pins and make the transceiver unusable.
6. Slide SFP28 in gently until it is fully seated.
7. Remove the rubber safety cap when you are ready to connect the cable to the transceiver.
Unit 4 Global Business Park, 14 Wilkinson Road, Cirencester, Gloucestershire, GL7 1YZ, United Kingdom.
DESCRIPTION
25GBASE-SR SFP28 850nm MMF 150m DDM LC
25GBASE-LR SFP28 1310nm SMF 10Km DDM LC
Advertisement
Summary of Contents for gbics GMZP088-VSL01D
- Page 1 25GBASE-SR SFP28 850nm MMF 150m DDM LC GSZP318-DSL10D 25GBASE-LR SFP28 1310nm SMF 10Km DDM LC This installation note provides the installation instructions for the GBICS.com SFP28 modules. These SFP28 modules are hot-swappable input/output (I/O) devices, which connect the module port with the fibre-optic or copper network.
- Page 2 Laser and LED Safety Guidelines and Warnings SFP28 transceivers are classified as Class 1M Laser Products (IEC 60825-1 2001–01). Observe the following guidelines and warnings: General Laser Safety Guidelines When working around ports that support optical transceivers, observe the following safety guidelines to prevent eye injury: •...
- Page 3 Laser Beam Warning Warning: Do not stare into the laser beam or view it directly with optical instruments. Waarschuwing Niet in de straal staren of hem rechtstreeks bekijken met optische instrumenten. Varoitus Älä katso säteeseen äläkä tarkastele sitä suoraan optisen laitteen avulla. Attention Ne pas fixer le faisceau des yeux, ni l’observer directement à l’aide d’instruments optiques. Warnung Nicht direkt in den Strahl blicken und ihn nicht direkt mit optischen Geräten prüfen.
- Page 4 ¡Atención! El extremo de un cable o conector de fibra sin terminación puede emitir radiación láser invisible. No se acerque al radio de acción ni lo mire directamente con instrumentos ópticos. La exposición del ojo a una salida de láser con determinados instrumentos ópticos (por ejemplo, lupas y microscopios) a una distancia de 100 mm puede comportar lesiones oculares.