Advertisement
Quick Links
Continuing section 6
Use the Help features of the interface to help you
configure the device. When you have finished
configuring the device, press 'Commit' to save the
changes, then 'Restart' to restart the device. You
can optionally press 'Reload' if you have further
configuration changes to make.
7
Check Your Setup
If your device is connected and configured correctly, you
will see the following LED Status:
POWER:
GREEN
LINK:
GREEN
COM:
GREEN
Troubleshooting
8
LED
Color
Airborne Device State
Adapter is not powered.
Adapter failed Power On Self Test (POST)
POWER
Adapter passed POST but is not configured for wireless
network communication.
Adapter passed post and is configured for wireless com-
munication.
Adapter is not powered.
(Periodic Blinking) Adapter is searching for a valid network
LINK
(Access Point) that matches device's configuration.
Adapter has successfully associated with an Access Point.
If Power LED is also Off then Adapter is not powered. If
Power LED is On then either:
• A physical connection detected on Serial/Ethernet cable.
• No TCP session from wireless interface has been estab-
lished.
No physical Serial/Ethernet connection has been detected.
(Blinking – OFF/Red) A physical Serial/Ethernet connection
has been detected and there is traffic across the interface. No
TCP connection to the adapter has been established on the
wireless interface.
COMM
A TCP connection to the adapter from the wireless interface
has been established but no physical connection on the Se-
rial/Ethernet interface has been detected
(Blinking – Green/Orange)
A physical Serial/Ethernet connection has been detected and
there is Serial/Ethernet traffic across the interface. A TCP
connection to the adapter has been established (On WLAN
or Ethernet interface).
A physical Serial/Ethernet connection has been detected. A
TCP connection to the adapter has been established from the
WLAN or Ethernet interface but no traffic has been detected.
Document number – PN710-00049-00_R2_ABDx-ER-DP551_0714qsg
More AirborneM2M Products
APMN-Q551
Embedded Dual Band M2M Access
Point Module
http://www.bb-elec.com/Products/Wireless-
Cellular/AirborneM2M-Embedded-Dual-Band-
Wireless-Module/AirborneM2M-Embedded-Dual-
Band-Access-Point-Module.aspx
APXG-Q5420
802.11 Wireless Router, Access Point and
Serial Device Server
http://www.bb-elec.com/Products/Wireless-
Cellular/Wireless-Ethernet-Bridge-Access-Point-
Client-Bridg/Airborne-Industrial-Wireless-Access-
Point.aspx
Fast, Easy Answers
First, check your LEDs.
Then use your smart
phone to access complete
documentation on our web
site. Simply scan the code
to the right or visit the
B&B Electronics Knowledge
Base:
http://support.bb-elec.com/knowledgec.aspx
1-888-948-2248 | Europe: +353 91 792444
www.bb-elec.com
707 Dayton Road | PO Box 1040 | Ottawa, IL 61350
Phone: 815-433-5100 | Fax: 815-433-5109
www.bb-elec.com | E-mail: info@bb-elec.com
© 2014 B&B Electronics Manufacturing Company
ABDx-ER-DP551 and
ABDx-ERDP551U
Wireless Ethernet Adapter
First Things First...
Before you begin, be sure you have
the following:
ABDx-ER-DP551 or ABDx-ER-DP551U
CD with Airborne Management Center
software
(ABDN-ER-DP551) 5 VDC power supply
with 2.1 mm barrel jack
OR:
(ABDN-ER-DP551U) Dual (Y) USB power
cable with 2.1 mm barrel jack
50 ohm, omni-directional antenna
www.bb-elec.com
Fast and easy on the web:
Advertisement
Summary of Contents for B&B ABDx-ER-DP551
- Page 1 If Power LED is also Off then Adapter is not powered. If Power LED is On then either: • A physical connection detected on Serial/Ethernet cable. ABDx-ER-DP551 or ABDx-ER-DP551U • No TCP session from wireless interface has been estab- lished.
-
Page 2: Product Overview
When AMC starts, it will request a login: Product Overview AMC will display the found Airborne device(s): LEDs Antenna Select Group Name: “manuf” and enter Group Tip: To easily convert a Direct Ethernet device to a bridge, use the Bridge Templates in AMC. For Password: “dpac”...