HANYOUNG NUX PZ1 Series Instruction Manual

Photo sensor
series
PZ1
INSTRUCTION MANUAL
Thank you for purchasing HANYOUNG product.
Before using the product, please read this instruction manual carefully.
Please keep this manual where you can view at any time
Safety information
Before using the product, please read the safety information thoroughly and use it properly.Alerts
declared in the manual are classified to Danger, Warning and Caution by their criticality
DANGER DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury
WARNING WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury
CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury
Danger
• Due to the danger of electric shock, use this product installed onto a panel while an
electric current is applied.
Warning
• The contents of this manual may be changed without prior notification.
• If you use the product other than manufacturer's designation, it may cause serious injury or loss.
• To prevent defection or malfunction of this product, supply proper power voltage in
accordance with the rating.
• Since this product is not designed with explosion-protective structure, do not
use it at any place with flammable or explosive gas.
• Remove this product while the power is off. Otherwise, it may cause malfunction or electric shock.
Caution
• Earth the Frame Ground (F.G) in case of using the switching regulator. Otherwise, they
may cause wrong operating by power switching noise.
• When using the sensor under the light such as fluorescent lighting or mercury lamp with
high frequency, block it with a light trap and avoid the lens from facing the light directly.
• Do not use an auto transformer. Use an insulating transformer to keep stable power voltage.
• If the cable needs to be extended, use over 0.3 ㎟ and be cautious of a possible sudden drop in voltage.
• Separate high voltage cable and power line from sensor wire. Be cautious since using a
same pipe arrangement for the wire could cause malfunction.
Specification
NPN PZ1-T1N
Model
PNP PZ1-T1P
Sensing method Through beam
Sensing distance 1 m
(Note 2)
Detectable object Min. Ø6 ㎜ Opague object
Power supply voltage
Current Trns : 20 ㎃ d.c max
Consumption Rcvr : 18 ㎃ d.c max
Output Mode
Control Output
Response
time
Hysteresis
Light source (Wave length)
LED
Sensitivity adjustment
CASE
Material
Lens
Protection Circuit
Connection Method
Ambient Illumination
Ambient Temp./Humidity
Case Protection
Vibration Resistance
Dielectric Strength
Shock Resistance
Insulation Resistance
Weight Trns, Rcvr : each about 50 g
(Note 1) IP67 protection is optional and there are no V/R and setting S/W
(Note 2) The sensing distance can be varied with size, Surface Condition, glossy, non-glossy of other of sensing object so that consider these facts.
(Note 3) PZ1-T1N(Throughbeam Type) is PZ1-TL1(Transmitter) and PZ1-TRN(Receiver).
(Note 4) Time Function(Off delay timer, built in : 0.1~2s) Variable. (Note 5) Dark On output mode is optional for limited reflective type.
PZ1-T5N PZ1-T7N PZ1-M1N
PZ1-T5P PZ1-T7P PZ1-M1P
Retro reflection
(Note3)
5 m 7 m 0.1 - 1 m
Min. Ø48 ㎜ Opague object Non-glossy and white paper 200×200 ㎜
Light ON or Dark ON selectable by convert switch
NPN Open collector output, Load current : 100 ㎃ d.c max(Resistive load), Remaining voltage : 1 V d.c max
PNP Open collector output, Load current : 100 ㎃ d.c max(Resistive load), Remaining voltage : 1 V d.c max
-
Control output indicator : Red LED(Red LED of transmitter of through beam type is for indicator of power supply)
Built-in Protection Circuit from reversed power supply connection, Output Short-Circuit (Overcurrent) protection
Sunlight : below 11000 Lux, Incandescent lamp : below 3000 Lux
10 - 55 Hz (cycle for 1 minute), double amplitude : 1.5 mm, in each direction X·Y·Z for 2 hours
HANYOUNGNUX CO.,LTD
28, Gilpa-ro 71beon-gil, Nam-gu, Incheon, Korea
HEAD OFFICE
TEL : (82-32)876-4697 F AX : (82-32)876-4696
http://www.hynux.net
PT. HANYOUNG ELECTRONIC INDONESIA
INDONESIA
JL.CEMPAKA BLOK F 16 NO.02 DELTA SILICON II INDUSTRIAL PARK LIPPO CIKARANG
FACTORY
CICAU, CIKARANG PUSAT, BEKASI INDONESIA 17550 TEL : 62-21-8911-8120~4 FAX : 62-21-8911-8126
• Avoid continuously switching the power source On and Off to use the product longer and
to avoid malfunction.
• This product is equipped with a structure (IP67), which allows partial waterproof but do not
use this product under water at all times.
• When the lens of the photo sensor is contaminated by foreign substance, use a dry cloth
to wipe off the substance. Never use thinner or organic solvents.
• Be cautious when you set sensitivity control, the volume may break by strong pressure or torque.
Suffix code
Model Code
PZ1-   
T
M
Sensing
method
and
R
Sensing
distance
Z
Output
Protective structure
(Cautious1)
PZ1-M2N PZ1-R10N PZ1-R30N
PZ1-M2P PZ1-R10P PZ1-R30P
Diffuse reflection
0.1 - 2 m 100 ㎜ 30 - 300 ㎜ 40 - 400 ㎜
12 - 24 V d.c (± 10 %)
30 ㎃ d.c max
1 ㎳ max
Infrared lighting diode
Built-in Sensitivity Control V/R (220˚rotation V/R)
PC(EXRL)
PC
3P (Throug-beam 2P), Ø 3.8 ㎜, Length 2 m
-25 ~ 55 ℃, 35 ~ 85 % RH (without freezing)
IP 65 (IP67 is optional)
1000 V a.c (at 50 / 60 ㎐ for 1 minute)
500 ㎨, 3 times each in X, Y and Z directions
20 ㏁ min (500 V d.c mega standard)
Approx. 60 g
3
Information
Small size photo sensor
1 1 m
5 5 m Through-beam
7 7 m
1 0.1 - 1 m
Retro-reflective
2 0.1 - 2 m
10 100 ㎜
30 30 - 300 ㎜ Diffuse-reflective
40 40 - 400 ㎜
3 10 - 30 ㎜
Limited-reflective
4 10 - 40 ㎜
T3 10 - 30 ㎜
Limited-reflective
※ OFF Delay, 0.1 - 2 sec
T4 10 - 40 ㎜
N NPN open collector output
P PNP open collector output
IP 65 : Standard type
IP 67 : Optional (No volume, setting switch)
PZ1-R40N PZ1-Z3N PZ1-Z4N
PZ1-R40P PZ1-Z3P PZ1-Z4P
Limited-reflective
10 - 30 ㎜ 10 - 40 ㎜
Non-glossy and white paper 50×50 ㎜
(Note 5)
Within 20 % of the sensing distance
ML1201KE130222
PZ1-ZT3N PZ1-ZT4N
PZ1-ZT3P PZ1-ZT4P
Limited-reflective (Timer function)
(Note 4)
10 - 30 ㎜ 10 - 40 ㎜
Light On (Dark On Option)
ON operation : 3 ㎳ max
On return : 100 ㎳ max
(With Minimum timer V/R)