Nortek Security & Control 500 Series Instruction Manual

INSTR,INSTL,WT00Z5-1; P/N: 10007350 B; INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: 8.500" x 11.000"; TOLERANCE ± .125"; SCALE: 1-1
Shown with supplied
decorative trim plate
NOTE: This unit must be added to the Network only where it will be permanently installed. The proper operation of this node in the
mesh network is dependent on it knowing its location with respect to other nodes. You cannot "test bench" confi gure this unit, then install.
WT00Z5-1
3-WAY WALL MOUNT ACCESSORY DIMMER SWITCH
™ ®
The GoControl family of Z-Wave certifi ed wireless Lighting Products (smart
LED fi xtures, bulbs, switches, dimmers, outlets and plug-in modules) Control
Products (thermostats, irrigation controller and garage door controller) and
Sensors (fl ood, leak, alert sounder, motion sensor and door/window sensor)
bring a new level of intelligent wireless Home Automation capability to
commercial and residential environments.
The Z-Wave wireless protocol is an international wireless standard for remote
home automation, security and other applications. This product can be included
and operated in any Z-Wave network with other Z-Wave certifi ed devices
from other manufacturers and/or other applications. All non-battery operated
nodes within the network will act as repeaters regardless of vendor to increase
reliability of the network.
The WT00Z5-1 Wall Mount Accessory Dimmer Switch allows remote ON/
OFF control and dimming of lights controlled by associated Z-Wave modules,
creating virtual 3-way switches. The WT00Z5-1 controls no load directly, so it
can be wired anywhere power is available, without the need for a traveler wire.
GoControl Z-Wave products are easy to install, are Z-Wave certifi ed, and allow
dealers to create an integrated wireless network with nearly limitless expansion
and interoperability with security, energy management, home entertainment,
appliances, and more.
DANGER! SHOCK HAZARD. Read and understand these instructions
before installing. This device is intended for installation in accordance with
the National Electric code and local regulations in the United States, or the
Canadian Electrical Code and local regulations in Canada. It is recommended
that a qualifi ed electrician perform this installation. For indoor use only. Retain
instructions for future use.
Z-WAVE PLUS FEATURES
The WT00Z5-1 contains a Z-Wave 500 Series Module that supports Z-Wave
Plus ® features. A Z-Wave certifi ed portable or stationary Controller can
communicate with the Z-Wave 500 Series Module.
Depending on the capability of the Controller or gateway software, the following
operations can be performed with the WT00Z5-1. Refer to the Controller or
gateway manual for details.
• Turn the Associated device ON and OFF.
• Dim the Associated device.
• Add or Remove the WT00Z5-1.
• Over-the-air firmware update by the gateway or static Controller.
PRINTER'S INSTRUCTIONS:
Scene and NWI Capable, 3-Way Wall Mount Accessory Dimmer Switch, Series 500
NEUTRAL
120 VAC
LINE
TO MOUNT MORE THAN ONE
WT00Z5-1 IN A BOX, SCORED TAB
WILL BREAK FLUSH WITH EDGE
OF PLASTIC
TAP TOP OR BOTTOM
OF SWITCH PADDLE
TO CONFIGURE
• Assign the WT00Z5-1 to a specific Group/Scene and/or to include the
Associated device as part of ALL ON or ALL OFF system commands.
• Lifeline function which automatically notifies the Associated modules and
the network that a manually reset device is no longer in the network, thus,
the corresponding Association becomes invalid.
INSTALLATION
Wire this switch in place of a current wall switch according to the diagram above.
✓ CAUTION! Do not wire unit "live" (with power on the circuit).
Adding to a network:
Refer to your Controller operating instructions to add this switch under the
command of the Wireless Controller.
1. With your Controller in Discovery or Add Mode, tap the switch. The LED will
blink slowly when in ADD Mode.
2. You should see an indication on your Controller that the "device was added"
to the network and the LED will stop blinking.
3. The device will appear in the list of Switches. It should display as a switch.
If the Controller/Gateway shows the addition failed, repeat Steps 1-3.
✓ NOTE: If you have trouble adding the WT00Z5-1 to a group it may be that
the Home ID and Node ID were not cleared from it after testing. You must
fi rst "RESET UNIT" to remove it from the network. Although adding it to a
group includes it in the network, removing it from a group does not remove it
from the network. If removed from a group, it functions as a repeater (only).
"RESET UNIT" removes it completely from the network.
To Reset Unit (If Required):
In the event that your primary Controller is lost or otherwise inoperable, to reset
the WT00Z5-1 and clear all network information, follow these steps:
1. Tap the top of the switch fi ve (5) times.
2. Press and hold the bottom of the switch for 15 seconds. The LED will
increasingly blink faster to indicate that a Reset is taking place.
Removing from a network:
The WT00Z5-1 can be removed from the network by the Controller/Gateway.
Refer to the Controller operating instructions for details.
1. Set the Controller into Removal Mode and follow its instruction to delete the
WT00Z5-1 from the Controller.
2. Remove the switch by tapping the paddle 2 times. The LED will begin
blinking slowly for 10 seconds indicating that it has been removed.
3. You should see an indication on your Controller that the "device was
removed" from the network.
WT00Z5-1
Z-Wave Radio Frequency (RF) Controlled, 120 VAC
WHITE
BLACK
PUSH ON (PUSH
& HOLD TO BRIGHTEN)
PUSH OFF
(PUSH AND
HOLD TO DIM)
GREEN GROUND
STATUS LED