Sony Remote Commander RM-V22 Operating Instructions

RM-V22.3-858-409-12 (1) Page1
RM-V22
Remote Commander
Operating Instructions
© 1996 by Sony Corporation
Printed in Malaysia
English
Notes on Batteries
WARNING
• Under normal conditions, batteries will last up to six months. If the
Commander does not operate properly, the batteries might be worn
This equipment has been tested and found to comply with the limits for
out. When replacing batteries, replace both of them with new ones.
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
• Do not mix old batteries with new ones or mix different types of
limits are designed to provide reasonable protection against harmful
batteries together.
interference in a residential installation. This equipment generates,
• If you take time to insert the batteries or press the buttons when
uses, and can radiate radio frequency energy and, if not installed and
replacing the batteries, the code numbers will be erased.
used in accordance with the instructions, may cause harmful
• If the electrolyte inside the battery should leak, wipe the
interference to radio communications. However, there is no guarantee
contaminated area of the battery compartment with a cloth and
that interference will not occur in a particular installation. If this
replace the old batteries with new ones. To prevent the electrolyte
equipment does cause harmful interference to radio or television
from leaking, remove the batteries when you plan not to use the
reception, which can be determined by turning the equipment off and
Commander for a long period of time.
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
Setting the Code
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
Step 1: Entering the Code Number
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
1 Set the slide switch on the Commander to
You are cautioned that any changes or modifications not expressly
the position that correspond to the desired
approved in this manual could void your authority to operate this
component.
equipment.
2 See the tables in "Component Code numbers," and find the code
number in double figures for the desired component.
If more than one code number is listed, use the number that's listed
first to complete the steps below.
Setting Up the Remote Commander
For example, if you're setting up a Philips' VCR, you would use the
Before you can start using the Commander, you must first set it up. code number 13.
This manual describes everything you need to know to set up the If your component isn't listed, see "Searching for the Correct Code."
Commander, including: 3 Press the SET button with a ball-point pen
• Installing the batteries. tip etc., and release it.
• Presetting the Commander with the codes for your TV, VCR, Cable 4 Enter the component's code number. For
box, and other audio components. example, if you're entering the code for a
Philips' VCR, you would press and release
1, then press and release 3.
Presetting the Remote Commander
5 Press and release the ENTER button to
The Commander is preset at the factory to operate Sony brand TVs ,
store the code number in the Commander's
VHS VCRs, receivers, and CD players. If you're using the Commander
memory.
with a Sony TV, VHS VCR, receiver, and CD player, you won't need to
6 Go to "Step 2: Checking if the Code Number Works" to finish setting
preset the Commander before you start using it.
up.
To set up the Commander to use with other (non-Sony) manufacturer's
components, you'll need to follow the instructions in this manual to
preset the Commander with the correct code number for your
Step 2: Checking if the Code Number Works
components.
1 Power on the component you want to set up with its power switch.
Note
2 Aim the commander at the component and
The Commander can be set up to operate only one component of each press the POWER button.
category (VCR, AV1, AV2, CBL, or TV position of the slide switch) at a The component should power off.
time - unless their code numbers happen to be the same. For example, 3 When the component powers off, check
you cannot set up the Commander to operate a Sony TV and a that the commander is operating the other
Panasonic TV at the same time (because they use different code
functions of your component, such as
numbers).
channel and volume control.
If the Commander Doesn't Seem to Be Working...
Installing the Batteries
• First, try repeating these setup procedures using the other codes
listed for your component (see "Component Code Numbers").
Slide open the battery compartment and insert two size AA (R6)
• If - after trying all the codes listed for your component - you still
batteries (not supplied).
cannot get the Commander to work properly, try the search method
Be sure to line up the + and – on the batteries with the + and – on the
described in "Searching for the Correct Code"
battery compartment.
1 2
If the Commander Seems to Be Working Properly...
3-858-409-12(1)
• You're finished setting up the Commander for your component.
• If you're setting up more than one component, you'll need to
complete these procedures for each component you plan to use with
the Commander.
• Use the label (supplied) to write down the code numbers of your
components. Then affix the label to the back of the Commander.
Changing the Component Type on the AV1
and AV2 Positions of the Slide Switch
On the positions AV1 and AV2 of the slide switch, the functions to
operate Sony brand receivers and CD player are preset at the factory
(using cord No. 4 and 5 respectively).
When you change the component type on the positions AV1 and AV2
of the slide switch, complete the following procedures:
1 Set the slide switch to the AV1 or AV2
AV2
AV1 CBL
position. VCR TV
2 Press the SET button with a ball-point pen
SET
tip etc., and release it.
3 Enter one of the codes from the following table, correspond to the
component type you're setting up:
Component type Code No.
VCR 1
Receiver 4
CD player 5
Tape deck 6
TV 8
Cable box 9
AV2
AV1 CBL
VCR TV For example, if you're setting up a CD player, you would press and
release 5.
4 Press and release the ENTER button to
ENTER
store the code number in the Commander's
memory.
To finish setting up the component, go to "Step 1: Entering the Code
Number" and complete the procedures that are described.
SET Searching for the Correct Code
If you've tried all the code numbers listed for your component and you
# #
still cannot get the Commander to work (or if your component is not
listed in this manual), try these steps.
1 Power on the component you want to set
AV2
AV1 CBL
up with its power switch. Then set the VCR TV
ENTER
slide switch on the commander to the
position that corresponds to the
component.
2 Press the SET button with a ball-point pen
SET
tip etc., and release it.
3 Press and release the CH+ button. Then
CH
POWER
press and release the POWER button.
4 Repeat step 3 until your component powers off.
Pressing the CH+ and POWER buttons repeatedly will try every
POWER POWER
available code until the correct one is found. It may take up to about 50
to 60 tries until the correct code number is located.
VOL CH
5 When the component powers off, press and
ENTER
release the ENTER button to store the code
number in the Commander's memory.
6 Check that the Commander is operating
VOL CH
the other functions of your component.
Turn on the component again; then press
the CH and VOL buttons. If the
Commander seems to be working
properly, you have completed setting up
the Commander.
If the component does not operate properly, repeat steps 2 and 5 and
search for another code. As the searching always start from 01, it will
stop again at the same code as the last searching. Pass the code and
continue searching until the next code which the component turns off.
If you still cannot get the Commander to work properly, see
"Troubleshooting."
Controlling the Volume of Video Remote Button Descriptions
Components Connected to an Audio System
Operating a TV
The Commander is factory preset based on the assumption that you
hear the sound of your video components from your TV's speakers,
and that you hear the sound of your audio components from the
1
loudspeakers via your receiver (or amplifier).
POWER
2
Even if you are operating a video or audio component, this feature
TC/VIDEO
enables you to control the volume of your TV or receiver without first VIDEO 1 VIDEO 2
1
having to change the Commander's slide switch to the TV or AV1.
3 TUNER
4
Position of the slide switch Controls the volume of
7
4
DISP
VCR TV
REC
CBL TV
TV TV
VOL
AV1 Component whose type is set on the 5
LIGHT
AV1 position*.
6
AV2 Component whose type is set on the
7 MUTING
AV1 position *. AV1
8 VCR
For example, to control the volume for your VCR channels, you don't
need to change the slide switch from VCR to TV.
* On the AV1 position, the receiver is preset at the factory (using code
No. 4). The commander controls the receiver's volume, even if you
assign a component which has no volume control itself (e.g. CD
1 To turn on and off.
player, VCR) on the AV1 position, when the slide switch is set to the
2 To change the input mode.
AV1 position.
3 To change the channel. For
Changing the Factory Preset of the Volume Control example, to change to channel
5, press 0 and 5 (or , press 5
If your video components are connected to an audio system, you
and ENTER.)
probably hear your TV or VCR's sound from the loudspeakers via your
4 To display the current channel
receiver, not from your TV speakers. In this case, you need to change
on TV.
the factory preset so that you can control the volume of your video
5 Volume up: +
components without first having to switch to the receiver (factory set
Volume down: –
on AV1 position). To change the factory preset of the volume control,
follow the procedures below.
You can change this either before or after you set up the Commander to
work with your component.
AV2
Operating a VCR
AV1 CBL
1 Set the slide switch to the position that you VCR TV
want to set up.
2 Press the SET button with a ball-point pen SET
tip etc., and release it.
1
3 aTo control the component's sound from POWER
2
the loudspeakers via your receiver which
TC/VIDEO
VIDEO 1 VIDEO 2
is assigned to AV1, press the VOL- button.
1
bTo control the component's sound from
3 TUNER
4
the loudspeakers via your receiver which
MUTING 4
7
is assigned to AV2, press the MUTING
5
DISP
button.
REC
6
cTo control the component's sound from
VOL
7
the TV speakers, press the VOL+ button.
8
4 Press and release the ENTER button to
VOL
ENTER 9
store your setting in the Commander's
LIGHT
memory.
!º
5 If you haven't already done so, finish setting up the component by
MUTING
completing the procedures in "Step 1: Entering the Code Number".
AV1
!¡ VCR
Using the Remote Commander
Operating a Component
AV2
1 Make sure that the slide switch is set to the
AV1 CBL
VCR TV
position that correspond to your desired
component.
2 Point the Commander directly at the component.
3 Press the button for the function you want to use.
See "Remote Button Descriptions" for complete descriptions of the
buttons on the Commander.
Notes on Using the Remote Commander
• Using the Commander will not increase the functions of your TV or
other components. The functions of the Commander are limited to
the functions of the TV or other components. For example, if your TV
doesn't have a MUTE function,. the MUTE button on the Commander
will not function with your TV.
• Using the LIGHT function frequently of the Commander will shorten
the battery life.
Operating a Cable box
6 To light up the Commander's 1
POWER
buttons. (The light will 2
SET
automatically turn off if no TC/VIDEO SLEEP
VIDEO 1 VIDEO 2 VIDEO 3
button is pressed for more than 1 2 3
9
3 TUNER CD TAPE
10 seconds.)
4 5 6
SET !º
SLEEP 7 To mute the volume on the TV.
7 8 9
VIDEO 3
2 3 Press again to turn muting off. 6
DISP ENTER
0
CD TAPE 8 Set to TV (AV1 or AV2 on
5 6 REC
which the TV is assigned).
8 9
9 To set up the Commander.
!¡
ENTER
0 !º To operate SLEEP function on
VOL CH
the TV. (Works only for a TV 7
LIGHT
with the SLEEP function.)
4
!¡ To change the channel. For 8
SHIFT
CH
MUTING RECALL
!™ example, to change to channel AV2
AV1 CBL
5 VCR TV
5, press 5 and ENTER.
!£ !™ Channel up: +
SHIFT
RECALL
AV2 Channel down: –
CBL
TV
!£ To operate JUMP,
FLASHBACK or CHANNEL
RETURN function on the TV
depending on the setting of the
TV's manufacturer.
1 To turn on and off.
2 To change the input mode.
3 To change the channel. For
!™
example, to change to channel
SET
SLEEP
5, press 0 and 5 (or , press 5
VIDEO 3
2 3
and ENTER.)
CD TAPE
5 6 4 To display the on-screen menu
8 9 (Sony VCR only).
!£
5 To record, press " while
ENTER
0
pressing r.
First release ", then release r.
!¢
6 To pause
CH
7 To rewind
!∞
8 To play
9 To stop
SHIFT
RECALL 0 To light up the Commander's
AV2
CBL
TV
buttons. (The light will
automatically turn off if no
button is pressed for more than
10 seconds.)
!¡ Set to VCR (AV1 or AV2 on
which the VCR is assigned)
!™ To set up the Commander.
!£ To change the channel. For
example, to change to channel
5, press 5 and ENTER.
!¢ To fast-forward
!∞ Channel up: +
Channel down: –
RM-V22.3-858-409-12(1) Page1
1 To turn on and off.
2 To set up the Commander
3 To change the channel. For
example, to change to channel
5, press 0 and 5 (or , press 5 and
ENTER.)
4 To light up the Commander's
buttons. (The light will
automatically turn off if no
button is pressed for more than
10 seconds.)
5 Set to AV1 or AV2 on which the
cable box is assigned.
6 To change the channel. For
example, to change to channel
5, press 5 and ENTER.
7 Channel up: +
Channel down: –
8 To operate JUMP,
FLASHBACK or CHANNEL
RETURN function on the TV
depending on the setting of the
TV's manufacturer.
Notes
• There may be cases you may turn
on/off the cable box by pressing the
CH+ or CH– buttons on the
Commander.
• If your cable box can control
volume, be sure to set its volume
control to a medium position. If the
volume on the cable box is turned
down completely, you will not be
able to adjust your TV's volume
with the Commander.