HANYOUNG NUX SSR-2 Series Instruction Manual

SSR-2
Single-Phase Solid State Relay
INSTRUCTION MANUAL
Thank you for purchasing Hanyoung Nux products. Please read the instruction
manual carefully before using this product, and use the product correctly.
Also, please keep this instruction manual where you can view it any time.
▍Safety information
Please read the safety information carefully before the use, and use the product correctly.
The alerts declared in the manual are classified into
DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury
WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury
CAUTION Indicates a potentially hazardous situation which, if not avoided, may result in minor injury or properties damage
DANGER
• The input/output terminals are subject to electric shock risk.
Never let the input/output terminals come in contact with
your body or conductive substances.
WARNING
• Please read the safety information carefully before the use,
and use the product correctly.
• If there is a possibility that a malfunction or abnormality of this
product may lead to a serious accident, install an appropriate
protection circuit on the outside and plan to prevent accidents.
• Please supply the rated power voltage, in order to prevent
product breakdowns or malfunctions.
• To prevent electric shocks and malfunctions, do not supply
power until the wiring is completed.
• Please disassemble the product after turning OFF the power.
• Any use of the product other than those specified by the
manufacturer may result in personal injury or property damage.
• Please use this product after installing it to a panel,
because there is a risk of electric shock.
▍Suffix code
Model Code
SSR-2 □ □ □ □ □ Single-Phase Solid State Relay
D 5 - 24 V d.c.
Input Voltage
A 100 - 240 V a.c.
10 10 A
20 20 A
Rated load current
30 30 A
40 40 A
2 90 - 264 V a.c. (Low voltage)
Rated load voltage
4 90 - 480 V a.c. (High voltage)
Z Zero Cross Switching (Standard product)
Operation method
(Switching Mode)
R Random Switching
▍Specifications
█ DC input
Low SSR-2D102Z
Model
High SSR-2D104Z
Low
Rated Load
Voltage High
Low
Peak Voltage
(Non-repetition)
High 800 V
L
Rated load current 10 A
O
A
Frequency
D
Low 170 A
Surge current
(8.3 ms No repetition)
High 170 A
Leakage current
Output ON voltage dropping
Rated Voltage
I
Operating Voltage Range
N
P Impedance
U
Operation Voltage
T
Input Current
Response Time
Insulating Resistance 500 V d.c., 100 ㏁ (Between the input / output and case)
Dielectric strength
Vibration resistance 10 - 55 ㎐, Double amplitude : 1.5 ㎜, X,Y, and Z direction for 2 hours
Shock resistance
Storage Temperature
Ambient Temperature
Ambient Humidity
Pollution level grade
Usage
Accepted standard
Weight
█ AC input
Low SSR-2A102Z
Model
High SSR-2A104Z
Low
Rated Load
Voltage
High
Low
Peak Voltage
(Non-repetition)
High 800 V
L
Rated load current 10 A
O
A
Frequency
D
Surge current Low 170 A
(8.3 ms No repetition)
High 170 A
Leakage current
Output ON voltage dropping
Rated Voltage
I
Operating Voltage Range
N
P Impedance
U
Operation Voltage
T
Input Current
Response Time
Insulating Resistance 500 V d.c., 100 ㏁ (Between the input / output and case)
Dielectric strength
Vibration resistance 10 - 55 ㎐, Double amplitude : 1.5 ㎜, X,Y, and Z direction for 2 hours
Shock resistance
Storage Temperature
Ambient Temperature
Ambient Humidity
Pollution level grade
Usage
Accepted standard
Weight
HANYOUNGNUX CO.,LTD
28, Gilpa-ro 71beon-gil, Michuhol-gu,
Incheon, Korea TEL : +82-32-876-4697
http://www.hynux.com
PT. HANYOUNG ELECTRONIC INDONESIA
Jl. Jangari RT.003/002 Hegarmanah Sukaluyu
Cianjur Jawa Barat Indonesia 43284
TEL : +62-21-5060-7210
Danger Warning
and according to their importance.
CAUTION
• Please make sure that the product specifications are the same
as you ordered.
• Please use the product in places where corrosive gases (especially
harmful gases, ammonia, etc.) and flammable gases are not generated.
• Please use the product in places without liquids, oils,
chemicals, steam, dust, salt, iron, etc. (pollution degree 1 or 2).
• Please avoid places where large inductive interference, static
electricity,magnetic noise are generated.
• Please avoid places with heat accumulation caused by direct
sunlight, radiant heat, etc.
• When water enters, short circuit or fire may occur, so please
inspect the product carefully.
• Do not connect anything to the unused terminals.
• For DC types, please wire correctly, after checking the polarity of the terminals.
• When disposing of the product, treat it as industrial waste.
•Since a heat sink corner is sharp, it would lead to a serious injury.
• When electricity flows, desktop or heat sink's corner temperature
would be high so that it could lead people to suffer burns.
•When it is out of order, please separate SSR from head sink and change only SSR.
•This model has epoxy molding for the purpose of safety,
reliability and extends of the life.
• When applying an electric current, SSR is heated more and more. So, it has
more durable at low heat sink temperature and ambient temperature.
Information
SSR-2D202Z SSR-2D302Z
SSR-2D204Z SSR-2D304Z
90 - 264 V a.c.
90 - 480 V a.c.
600 V
1,200 V
20 A 30 A
50/60 ㎐ (Dual usage)
260 A 420 A
250 A 370 A
Less than 20 ㎃
Less than 1.6 V (R.M.S)
5 - 24 V d.c.
4.6 - 32 V d.c.
Less than 4 ㏀
More than4.6 V d.c.
Constant-current system : 8 ㎃ (±3)
1/2 Cycle + 1 ms max. ("R"type below 1 ms)
2,500 V a.c. (For 1 min at 60 ㎐)
1,000 ㎨, X,Y,Z each axis 3 times
-30 ~ 90 ℃
-5 ~ 40 ℃ (But without frostiness)
45 ~ 85 % RH
2level pollution
Resistive load / Inductive load
IEC 62314
Approx. 89g
SSR-2A202Z SSR-2A302Z
SSR-2A204Z SSR-2A304Z
90 - 264 V a.c.
90 - 480 V a.c.
600 V
1,200 V
20 A 30 A
50/60 ㎐ (Dual usage)
260 A 420 A
250 A 370 A
Less than 20 ㎃
Less than 1.6 V (R.M.S)
100 - 240 V a.c.
70 - 264 V a.c.
Less than 40 ㏀
More than 70 V a.c.
220 V a.c. : 8 mA
1/2 Cycle + 1 ms max. ("R"type below 1 ms)
2,500 V a.c. (For 1 min at 60 ㎐)
1,000 ㎨, X,Y,Z each axis 3 times
-30 ~ 90 ℃
-5 ~ 40 ℃ (But without frostiness)
45 ~ 85 % RH
2level pollution
Resistive load / Inductive load
IEC 62314
Approx. 89g
▍Dimensions
MC0801KE180713
▍Connection
※ This model does not have a fuse internally. So we suggest using fast-acting fuse separately on the outside as following picture.
█ SSR-2D
▍Input/Load/Surge current Characteristics
Input current Characteristics
SSR-2D
•SSR-2□20
SSR-2D402Z
SSR-2D404Z
•SSR-2□10
40 A
▍Installation
•Please make intervals more than the sizes in the
following picture.
•Please install wiring duct less than half the height of
the heat sink to prevent the flow of air.
•It is good to use Hanyoung Nux's SSR in lower than
ambient temperature 40 ℃ so, please use it lower
than standard temperature.
•When installing the SSR, be sure to installthe heat sink
in the vertical direction.
•Unavoidably, if installed horizontally, theperformance
of the product will drop below 50 %
▍HEAT SINK
█ Model : HSP series
[Unit : mm]
SSR-2A402Z
SSR-2A404Z
40 A
Model Applicable Model
HSP-10
HSP-20
HSP-40
▍Precautions during the use of Heat Sink
[단위 : mm]
█ SSR-2A
SSR-2A
Load current Characteristics
10 A ~ 20 A
L
Ø4.5
45
114
Capacity(A)
SSR-2□10□ 10 A
SSR-2□20□ 20 A
SSR-2□30□ 30 A
SSR-2□40□ 40 A
• Using standard heat sink is mandatory for this product.
• Even the standard heat sink is used, SSR damage may occur if the environment temperature
rises or if the ventilation does not work well. (Environment temperature : over 40 ℃)
•The normal SSR element is damaged at the maximum temperature of 125 ℃ . When the
temperature of heat sink is 85° C, the temperature of the element reaches around 125 ℃ .
Therefore, during operation, measure the temperature of heat sink.
•When you connect SSR onto the heat sink, heat-transmitting grease is needed for smooth
heat transmission.
• To prevent separation by vibration, tighten up with bolts.
• Do not use any insulating materials such as wood, plastic or rubber. The standard heat sink
must be greased on the bottom side as shown below and connected.
※ The heatproof silicon grease must be applied thoroughly on the heat sink as well as the
bottom of SSR. The case side of heat sink needs to be installed on up and down directions.
▍Equivalent Circuit
Surge current Characteristics
30 A ~ 40 A
•SSR-2□40
•SSR-2□30
9.8×R2.2
35.1
Length(L)
48 mm
80 mm
109 mm