Advertisement
GT-222ES, SRM-222ES, F226S, T226S, C226S
10-21U-00
SERVICE DATA
TRIMMER/BRUSHCUTTER
GT-222ES/SRM-222ES
ECHO:
shindaiwa:
(Serial number : 37000001 and after)
INTRODUCTION
W e are constantly working on technical im-
provement of our products. For this reason,
technical data, equipment and design are
subject to change without notice. All speci-
fications and directions in this SERVICE
DATA are based on the latest product infor-
mation available at the time of publication.
F226S/T226S/C226S
STAGE
MODEL
1 SERVICE INFORMATION .............................. 2
1-1 Specifi cation ............................................... 2
1-2 Technical data ............................................. 3
1-3 Torque limits................................................ 4
1-4 Special repairing materials ......................... 4
1-5 Service limits............................................... 5
1-6 Special tools ............................................... 6
2-1 General adjusting rules ............................... 7
2-3 Adjusting carburetor.................................... 8
CONTENTS
Reference No.
10-21U-00
I S S U E D :
2 0 1 2 0 6
1
1
page
Advertisement
Table of Contents
Related Manuals for Yamabiko Echo SRM-222ES
Summary of Contents for Yamabiko Echo SRM-222ES
-
Page 1: Table Of Contents
GT-222ES, SRM-222ES, F226S, T226S, C226S 10-21U-00 SERVICE DATA TRIMMER/BRUSHCUTTER GT-222ES/SRM-222ES ECHO: F226S/T226S/C226S shindaiwa: STAGE MODEL (Serial number : 37000001 and after) INTRODUCTION CONTENTS page W e are constantly working on technical im- 1 SERVICE INFORMATION ......2 provement of our products. For this reason, 1-1 Specifi... -
Page 2: Service Information
320 (12.6) 420 (16.5) Dry weight* kg (lb) 4.5 (9.9) 5.1 (11.2) 5.2 (11.4) Engine Type YAMABIKO, air-cooled, two-stroke, single cylinder Rotation Anticlockwise as viewed from the output end Displacement 21.2 (1.29) Bore mm (in) 32.2 (1.27) Stroke mm (in) 26.0 (1.02) -
Page 3: Technical Data
GT-222ES, SRM-222ES F226S, T226S, C226S SERVICE INFORMATION 1-2 Technical data GT-222ES SRM-222ES (L) SRM-222ES (U) Model F226S T226S C226S Engine Idling speed r/min 3,000 +/- 400 Wide open throttle speed r/min 6,700 - 7,700* 9,000 - 10,000* 10,500 - 11,500** Clutch engagement speed r/min 3,750... -
Page 4: Torque Limits
GT-222ES, SRM-222ES SERVICE INFORMATION F226S, T226S, C226S 1-3 Torque limits Descriptions Size kgf •cm N•m in•lbf Starter Starter pawl assembly 80 - 100 8 - 10 70 - 90 system Starter case M 4* 30 - 45 3 - 4.5 25 - 40 Ignition Flywheel 160 - 200... -
Page 5: Service Limits
GT-222ES, SRM-222ES F226S, T226S, C226S SERVICE INFORMATION 1-5 Service limits 5K268 5K228 5K229 5K230 5K231 5K016 5K042 5K269 5K219 5K171 5K232 Description mm (in) A Cylinder bore When plating is worn and aluminium can be seen Piston outer diameter Min. 32. -
Page 6: Special Tools
GT-222ES, SRM-222ES SERVICE INFORMATION F226S, T226S, C226S 1-6 Special tools Key Part Number Description Used for: G310-000050 Tachometer PET-304 Measuring engine speed to adjust carburettor 363018-00310 Washer Installing crankcase oil seal X605-000050 Torx L wrench Removing and installing bolt 897603-23030 PTO shaft puller Removing driven (PTO) shaft 897701-06030... -
Page 7: Carburetor Adjustment Procedure
GT-222ES, SRM-222ES F226S, T226S, C226S SERVICE INFORMATION 2 CARBURETTOR ADJUSTMENT PROCEDURE 2-1 General adjusting rules A. Before starting the unit for adjustment, check the following items. 1. The correct spark plug must be clean and properly gapped. 2. The air fi lter element must be clean and properly installed. 3. -
Page 8: Adjusting Carburetor
GT-222ES, SRM-222ES SERVICE INFORMATION F226S, T226S, C226S 2-3 Adjusting carburettor SRM-222ES, T226S, C226S: Remove shield and cut trimmer head line lengths to 180 mm. GT-222ES, F226S: Cut trimmer head line lengths to 130 mm with shield. (normal lengths : 145 mm cut by shield knife.) 1.