Advertisement
Quick Links
User Guide
SPECIFICATIONS
PRECAUTIONS
PREPARATION
FLEX RGB Series - T20100
Color
Model
Red
Green
FLEX RGB T20100
Blue
White
*Electronic dimming control is supported
Use precautions to avoid damages to the product or injuries of users. Any actions against following contents will cause serious
issues such as malfunction, electric shock, or burn.
DC12V
USE DC12V ONLY
AC INPUT
DO NOT USE AC INPUT
Do not cut or rejoion wires while product
is connected wth live power source
Avoid performing installation under rain or
high humidity for outdoor use
Do not use the product under circumstances
listed below
- High temperature spots over 60˚C (140˚F)
- Spots draw extreme moisture or dust
- Spots have corrosive gas or highly effectied
by electromagnetic field
TOOLS REQUIRED
Wire Stripper, Drill, Screw Driver, Wiper
PREPARE CHANNELS
1. Clean moisture and dust inside
1. Wipe out dust, water, and oil inside. 3M tape will come off easily if product is mounted on uncleaned surfaces.
2. Make holes for wires from modules to SMPS.
3. Without bushins, wires will easily be cut and short-circuit will occur.
*Use white paint inside the channels for better reflection
DAEHANTRANS CO.,LTD
#7-11 Songdo-Dong, Yeonsu-Gu, Incheon, Korea
Tel. +82 32 858 0491 Fax. +82 32 832 8421 enquiry@daehantrans.com / www.daehantrans.com
Power
Operating
Weight
Consumption
Power
5.0W
3.6W
DC12V
98g
3.9W
12W
IP65
Cut Mark
SUPPLIES REQUIRED
Wire Nuts, Cable Ties, IDC Connectors, VCTF(PLTC) Cable,
Super Glue, Silicon(optional)
2. Make holes
Min Bending
Viewing
Radius
Angle
120 °
R20mm
3cut
Do not perform actions listed below
- Alter or modify
- Touch LED lamps with sharp objects
- Put glue or silicon over the LED lamps
Maximum driver quantity per serial
connection is limited. Failure causes overload
of current and damages to the product
Refer to 'WIRE THICKNESS' table to use proper
wire thickness between SMPS and the first
LED module
Failure will cause dimmed output
Cable length between SMPS and the first LED
module is limited. Refer to 'CONNECTION
WITH POWER SUPPLY' on page 2
3. Use bushing to protect wires
1
Max Serial
Connection
3M (3 Units)
Advertisement
Summary of Contents for DAEHAN FLEX RGB Series
-
Page 1: Specifications
User Guide FLEX RGB Series - T20100 SPECIFICATIONS Power Operating Min Bending Viewing Max Serial Color Model Weight Consumption Power Radius Angle Connection 5.0W Green 3.6W 120 ° FLEX RGB T20100 DC12V R20mm 3M (3 Units) Blue 3.9W White *Electronic dimming control is supported... - Page 2 User Guide FLEX RGB Series - T20100 BEFORE HANDLING UNITS Do not flex or bend units with less than 20mm in radius, 40mm in diameter. Refer to left illustration. R20mm When stored in cold weather, units are stiff. Connect them with power supplies and wait until they become soft enough to be easily fabricated.
- Page 3 User Guide FLEX RGB Series - T20100 INSTALLATION GUIDE 1. DETERMINE LAYOUT MATERIAL ESTIMATE Attention to : John Doe Page 1 of 1 DOUBLE LAYOUT R30mm or more Connection Stroke Width : 80mm Connection R30mm R30mm Channel Depth : 80mm...
- Page 4 User Guide FLEX RGB Series - T20100 LAYOUT GUIDE TROUBLE SHOOTING Entire sign or leg does not light after Check connection from power supply lead to first module. Make sure polarity of connections made at the power complete installation. supply lead and any jumper wire is correct. Power supply outputs should be connected red-to-red and white-to- white.