Advertisement
Quick Links
A P L A Y
C
O R
E
C
O
M
P A N Y
Enriching Childhood Through Play
1−800−235−2440
ISSUED/REVISED:
06/20/05
INSTALLATION
=
DETAIL
PARTS LIST
=
REFERENCE
YEARS OLD
NOTE: REGULAR MAINTENANCE
REQUIRES LUBRICATION OF SWIVEL
ASSEMBLY WITH STANDARD
AUTOMOTIVE GREASE. A GREASE
FITTING IS INCLUDED IN THE
SWIVEL ASSEMBLY FOR THIS
PURPOSE. IN AREAS OF HIGH USE,
LUBRICATION INTERVALS SHOULD
BE INCREASED ACCORDINGLY.
R
R
SM
0'-12 1/2" [31.75cm]
FROM FINISHED SURFACE
TO BOTTOM OF TIRE
ASSEMBLY DRAWING
10777 SHOWN
INSTALLATION
INSTRUCTIONS
STEP 1: Before assembling this equipment,
read the enclosed Installer Instructions in the
installation booklet; follow all the instructions
during installation.
STEP 2: Assemble parts as shown in the
Assembly Drawing. Refer to the assembly
details for the specific hardware required in
each connection.
STEP 3: Loctite (supplied by others) should be
used on all threaded hardware.
10777
TIRE
SWING
NOTE: 10778 ADD−A−BAY
Advertisement
Summary of Contents for Gametime Tire Swing
- Page 1 10777 TIRE A P L A Y P A N Y SWING Enriching Childhood Through Play 1−800−235−2440 ISSUED/REVISED: 06/20/05 NOTE: 10778 ADD−A−BAY INSTALLATION DETAIL PARTS LIST REFERENCE YEARS OLD 0'-12 1/2" [31.75cm] FROM FINISHED SURFACE TO BOTTOM OF TIRE ASSEMBLY DRAWING 10777 SHOWN NOTE: REGULAR MAINTENANCE REQUIRES LUBRICATION OF SWIVEL...
-
Page 2: Assembly Drawing
EXISTING TOPRAIL ASSEMBLY 0'-12 1/2" [31.75cm] FROM FINISHED SURFACE TO BOTTOM OF TIRE NOTE: REGULAR MAINTENANCE REQUIRES LUBRICATION OF SWIVEL EXISTING UPRIGHT ASSEMBLY WITH STANDARD AUTOMOTIVE GREASE. A GREASE FITTING IS INCLUDED IN THE ASSEMBLY DRAWING SWIVEL ASSEMBLY FOR THIS PURPOSE. - Page 3 14'-5 9/16" [440.85cm] 2'-0" [60.96cm] DIA. x 2'-6" [76.20cm] DEEP (4 REQUIRED) SEE DETAIL 005 4'-1" [124.46cm] 15'-0 3/8" [458.08cm] 10777 NOTE: HOLE DEPTHS INDICATED CONCRETE REQUIRED: ON ALL GROUND PLANS ARE (PER GROUND HOLE) GROUND PLANS MEASURED FROM THE FINISHED .17 CUBIC YARDS SURFACE.
- Page 4 DETAILS −for− 10777 & 10778 MPORTANT ASTM F1487, A EDUCE THE ISK OF LOTHING NTANGLEMENT IN OMPLIANCE WITH ROTRUDING HREADS EYOND THE ACE OF THE HALL LUSH ILED MOOTH AND REATED TO REVENT ORROSION FTER SSEMBLY IS OMPLETE UTS AND LATWASHERS TO ATCH ADIUS OF...
-
Page 5: Top Views
*38'-6 1/16" [11.74M] 11'-0" [3.35M] RADIUS (TYPICAL) 33'-9 3/4" [10.31M] 5'-10 7/8" [1.80M] RADIUS (TYPICAL) [1.80M] ALL AROUND 10777 TOP VIEWS NOTE: 1.) OWNER/OPERATOR SHALL INSTALL AND 14'-5 9/16" [4.41M] MAINTAIN PROTECTIVE SURFACING WITHIN THE USE ZONE (U.S.) OR PROTECTIVE SURFACING ZONE (CANADA) OF ALL PLAY EQUIPMENT TO COMPLY WITH ASTM F-1292 AND ASTM F-1487 4'-6"... - Page 6 DETAILS −for− 10777 & 10778 MPORTANT ASTM F1487, A EDUCE THE ISK OF LOTHING NTANGLEMENT IN OMPLIANCE WITH ROTRUDING HREADS EYOND THE ACE OF THE HALL LUSH ILED MOOTH AND REATED TO REVENT ORROSION FTER SSEMBLY IS OMPLETE UTS AND LATWASHERS TO ATCH ADIUS OF...