Littelfuse MiniFlec Series Installation Sheet

Installation Instructions
MiniFlec Series Power Distribution Module
Part Number: LFMX0007Z-01
Description
The standard MiniFlec is a compact, front access, internally
bussed, connectorized, sealed power distribution module,
suitable for mounting in rugged commercial vehicle
applications. The MiniFlec is a product that has dense
concentration of high power circuits and accepts plug devices
like automotive fuses, diodes and relays to protect and control
complex electrical systems. An internally mounted Printed
Circuit Board (PCB) allows bussed connections to a large
number of devices.
Installation
Assemble the PDM and mount to a surface following the
below sequence:
1. Fill the available fuse and relay spots to match the the
application needs. Check the locations on the fuse and
relay table for the maximum fuse and relay ratings for
each space and do not exceed the maximum rated values.
2. Use the mounting hole pattern on the mounting surface
and mark the mounting hole pattern. Drill the holes so
they are sized for M6 bolts. Place the MiniFlec over the
pattern and bolt it in place. Torque down the mounting
screws to 12-15Nm (4.5-5.9 ft-lb).
3. The harnesses should be made to match the terminal
map on the schematic. The connectors should now be
attached. Each has a unique key that should prevent
misassembly. Make certain that the connectors are fully
inserted and the secondary lock is fully engaged. If the
secondary lock will not fully engage, the connector is not
fully connected. Be sure that the output cables are routed
so they have sufficient bend radius and are not at risk
of being damaged or pinched. Lastly, make sure that all
cables are strain relieved by being supported within 18"
of the battery.
Step by step images shown in Figure 1 on page 2.
© 2018 Littelfuse Commercial Vehicle Products
littelfuse.com
Specifications Overview
Max Load:
Fuse Rating Ranges:
Color:
Housing:
Ingress Protection:
Input Stud:
Mating Terminals & Seals
Working Voltages:
LFMX0006Z-01
Input Stud Torque:
Mounting Bolt Torque:
Vibration Resistance:
Operating Temp:
Dimensions (LxWxH):
Accessories:
Relay Capacity:
FUSE
LOCATION
F01
F02
F03
F04
F05
F06
F07
F08
F09
F10
F11
F12
F13
F14
Ordering Information
PART NUMBERS
LFLM0007Z-01
A custom MiniFlec can be built specific to your design
requirements and is a special order product. Please talk to
your local representative for additional details.
1 of 3
150A
MINI Fuse: 2-30A
®
MCASE+ Fuse: 15-60A
®
Black
Glass Renforces Nylon (94V-0)
IEC 529 IP67/69K
M8
Tyco HDSCS Series Connectors
with MCP Terminals
Tyco 1-1564542-1
Tyco 1-1418437-1
Tyco 2-1564514-1
Tyco 1-1670894-1
9-16V with 12V Relays
18-32V with 24V Relays
12-15Nm
12-15Nm
ISO 16750-4
-40°C to +85°C
157mm x 96mm x 126mm
Fuse Puller, Spare Fuses Tether
3 Form C 280 Series Micro Relays,
3 Form A Ultra Micro Relays,
1 ISO Micro Relay
MAX FUSE RELAY
VALUE LOCATION
30A K01
30A K02
30A K03
20A K04
20A K05
20A K06
50A MCASE K07
30A
20A
30A
30A
30A
60A MCASE
20A
DESCRIPTION
Standard Unloaded MiniFlec Power
Distribution Module
MAX RELAY
VALUE
35A
35A
35A
20A
20A
20A
40A
Rev: 081718