Advertisement
Quick Links
Includes m odels
MAS1020-01
MAS1220-01
MOS1220-01
MGS0615-01
Introduction
Thank you for purchasing a Heavy Duty Metal Hose Reel.
The range of single pedestal reels have been designed
using the highest quality, heavy gauge materials and are
fitted with purpose specific hose and swivels. Models
available are for Air/Water, Oil and Grease
Important Information
PLEASE READ THIS SAFETY INFORMATION
CAREFULLY BEFORE USE.
Read and retain this instruction manual to assist you in the
operation and maintenance of this product.
'Cautions' are listed throughout this manual to advise of
actions that may cause damage to your equipment.
CAUTION
Make sure the line pressure does not exceed the rated
operating pressure of your model hose reel, refer
specifications.
CAUTION
Exposure of the skin directly to pressurized air or fluid
could result in severe bodily injury.
CAUTION
Before carrying out any maintenance turn off and
disconnect the supply line to the reel and carefully
release the hose line pressure.
Installation Procedure
1) For overhead ceiling mounting: Install reel at least 3m
(10 feet) above the floor.
2) You will need to purchase the appropriate hardware for
mounting your new reel.
3) The reel base has four 1/2" (12.7mm) drilled holes for
mounting on a suitable flat surface.
4) The reel is supplied with a hose guide roller bracket.
The roller bracket position may be changed depending on
the reel mounting position. Figure 2 shows " Typical
mounting positions". If the bracket position needs to be
changed, do the following:
SK110 Issue 8 © 2017
SINGLE PEDESTAL
METAL HOSE REEL
INSTRUCTION MANUAL
A) Pull out some hose and let reel latch.
B) Remove the 4 bolts that attach the guide roller bracket
to the support post.
C) Rotate guide roller bracket to correct position, then
replace all bolts and tighten.
5) Using the four holes in the base, mount the reel in the
desired location. Be sure to use the appropriate hardware
and tighten securely.
6) Apply Teflon tape or pipe sealant to supply line threads,
attach to reel and tighten. The other end of the oncoming
line can now be connected to the desired supply source.
Tighten stopper bolts, and unlatch the reel.
7) Apply Teflon tape or pipe sealant to the outlet fitting on
the hose, then attach the desired tool or nozzle. Check
connections for leakage, also check hose reel for correct
operation. (See Operation section)
Page 1 of 4
Advertisement
Summary of Contents for Macnaught MAS1220-01
- Page 1 Includes m odels SINGLE PEDESTAL MAS1020-01 MAS1220-01 METAL HOSE REEL MOS1220-01 MGS0615-01 INSTRUCTION MANUAL Introduction Thank you for purchasing a Heavy Duty Metal Hose Reel. The range of single pedestal reels have been designed using the highest quality, heavy gauge materials and are fitted with purpose specific hose and swivels.
- Page 2 Maintenance Procedures 8) If hose stopper adjustment is required, pull hose from 4) Re-insert hose through guide, and install stopper onto the reel and allow to latch at desired length. Loosen hose end. stopper bolts and slide stopper to a position close to the hose guide.
- Page 3 Maintenance Procedures 9) Feed the hose through the hose guide, fit the hose 3) Carefully unlatch the reel and firmly hold the drum. Allow the drum to slowly unwind until it stops. stopper, then unlatch the drum and allow the hose slowly to retract 4) Remove the swivel, circlip and spacer.
- Page 4 This product should be disposed of according to all applicable local and national government environment regulations and guidelines. For Warranty Terms and Conditions see macnaught.com.au For a list of Australian Service Centres see macnaught.com.au SK110 Issue 8 © 2017 Page 4 of 4...