Phoebe LED Atlas-Mini series Operation Instructions

This instruction sheet is relevant to Phoebe LED Atlas-Mini LED Slimline Floodlights with part codes:
6416, 6423, 6430, 6447, 6454, 6461, 7581, 7598, 10314, 10321, 10338, 10345, 10352, 10369, 10376, 10383
THANK YOU for buying this PHOEBE LED product. To help ensure this luminaire gives complete satisfaction please only use it according to the
following instructions, and then pass the instructions to the appropriate person for retention and future reference.
Warning
1. Installation only to be carried out by a qualified electrician
2. Please ensure surface is suitable and capable of holding the lamp weight
3. Do not operate if product is damaged
4. Suitable for use outdoors IP66 rating
5. This product is not suitable for fire rated installations

Specifications:

Part Codes
PIR sensor
Wattage
fitted
Black White
7581 10314 No 10W
6416 10338 No
20W
6430 10352 No
30W
6454 10376 No 50W
7598 10321 Yes
10W
6423 10345 Yes
20W
6447 10369 Yes 30W
6461 10383 Yes
50W
Dimensions:
Part Codes
Wattage Width (W) Height (H) Depth (D) Depth inc. PIR (D2)
Black White
7581 10314 10W
140mm
6416 10338 20W
201mm
6430 10352 30W 201mm
6454 10376 50W 298mm
7598 10321 10W 140mm
6423 10345 20W
201mm
6447 10369 30W
201mm
6461 10383 50W 298mm
BEFORE YOU START
PLEASE READ ALL THE
INSTRUCTIONS CAREFULLY
PRIOR TO INSTALLATION
Turn power
off at the
mains
ONLY ONCE INSTALLATION
IS COMPLETE
Turn power
back on at
the mains
CIRCUIT TESTING
For high voltage circuit insulation
testing disconnect mains input
supply first
(Do not circuit test using a Megger)
Images are for information only. Phoebe LED shall not be held liable for improper operation of the luminaire in circumstances where procedures and
Tel: +44 (0)1274 657 088 Fax: +44 (0)1274 657 087 Web: www.phoebeled.com
Power
Voltage IP Rating
Factor
>0.5
>0.5
>0.9
>0.9
240V
IP66
50/60Hz
>0.5
>0.5
>0.9
>0.9
126mm 30mm -
166mm 34mm -
166mm 34mm -
226mm 40mm -
188mm 30mm 51mm
216mm 34mm 51mm
216mm 34mm 51mm
272mm 40mm 55mm
Fitting:
1. Mark drill points and drill fixing holes and hole for power
cable (if required)
2. Align luminaire and fix in place surface using bolts/
fixtures suitable for chosen surface, the angled bracket
allows access to mounting points without the need to
disassemble the fitting
Angle Adjustment:
1. Angle floodlight to desired angle
2. Tighten socket head screw to prevent unit from moving
Wiring Instructions:
1. Installation only to be carried out by a qualified electrician
2. 240V mains cable connection should be made with a
suitable IP65 junction box
3. Connect power lead to 240V mains electricity in
accordance with current wiring regulations
(see wiring diograms overleaf)
Operation Instructions (for PIR Sensor Only):
• The monitoring angle is up to 120°
• Depending on the angle of the sensor the monitoring range
has a maximum detection distance of 12m
• Lighting time length can be adjusted from 10 seconds (±3 sec)
turning clockwise up to 8 minutes (±2 min) after detection
• Dusk-til-Dawn detection can be manually adjusted by turning
the LUX dial to allow for light levels/time of year
(for daylight sensor testing turn fully to sun position)
• Sensitivity of the motion sensor can be changed by adjusting the SENS dial effective range 5m to 12m
specifications have not been followed correctly.
IP66 IK08
Useful Total
IK Rating
Lumens Lumens
760lm 900lm
1450lm 1600lm
2200lm 2400lm
3850lm 4200lm
IK08
760lm 900lm
1450lm 1600lm
2200lm 2400lm
3850lm 4200lm
W
H
Cable Insulation
VDE H05RN-F
3G 1.0mm
Class I
VDE H05RN-F
4G 1.0mm
W
D
H
Socket
Head
Screw
To 240V
Mains
PIR tilt
& Twist
Settings are on the
Rear of the PIR
Ambient
Operating Temp
-20°C to 40°C
D
D2