Advertisement
Quick Links
IMPORTANT:
Thank you for purchasing this CBI product. Please read through this entire document before proceeding with installation. If you are not
confident in your mechanical skills, please seek the help of a professional to perform the installation. Check your packages immediately
upon arrival to ensure that everything listed is included, and to check for damage during shipping. If anything is missing or damaged, or
if you need technical assistance with any aspect of this installation, call CBI at (208) 528-0664 as soon as possible.
Hardware:
• (2) –7/16" X 4" grade 8 bolts
•(4) –7/16" X 1" Grade 8 bolts
•(6) –7/16" serrated flange nuts
•(6) –7/16" SAE Washers
•(2) –½" X 1 ½" Grade 8 bolts
•(2) –½" serrated flange nuts
•(2) –½" SAE washers
•(2) –½" Strut washers zinc
•(6) –Black strut washers
•(2) –Side support brackets
License Plate Hardware:
•(2) –¼" X ½" S.S. button head bolts
•(2) –¼" serrated flange nuts
Fog Lights:
•(4) –¼" X ½" S.S. button head bolts
•(4) –¼" serrated flange nuts
•(2) –5/16" X ¾" hex head bolts
•(2) –5/16" SAE washers
•(2) –5/16" serrated flange nuts
•(2) –fog light brackets
(left and right specific)
Power Steering Cooler Relocation
Brackets:
•(2) –¼" X ¾" hex head bolts
•(2) –¼" SAE washers
•(2) –¼" serrated flange nuts
•(2) –Power Steering Coolerbrackets
Winch Plate:
•(6) –3/8" X ¾" S.S. button head bolts
•(6) –3/8" serrated flange nuts
For questions or
further help:
Call: 866-522-0697
Email: info@cbioffroadfab.com
page 1–5
T 3 F R O N T B U M P E R I N S T A L L A T I O N I N S T R U C T I O N S
T3 Tacoma
Front Bumper
i n s t a l l a t i o n i n s t r u c t i o n s
Applications
These installation instructions apply to the following CBI Off Road products
T3-FB
T3-FB-PRO
T3-FB-CGP
T3-FB-CGP-PRO
T3-FB-FGP
T3-FB-FGP-PRO
Side Support Brackets
Power Steering Cooler Bracket
2016+ Tacoma Front Plate Bumper
2016+ Tacoma Aluminum Front Plate Bumper
2016+ Tacoma Front Plate Bumper w/Center Grill Protection
2016+ Tacoma Aluminum Front Plate Bumper w/Center Grill Protection
2016+ Tacoma Front Plate Bumper w/Full Grill Protection
2016+ Tacoma Aluminum Front Plate Bumper w/Full Grill Protection
Fog light mounting brackets
Zince strut Washers
Black Strut Washers
Advertisement
Summary of Contents for CBI T3-FB
- Page 1 IMPORTANT: Thank you for purchasing this CBI product. Please read through this entire document before proceeding with installation. If you are not confident in your mechanical skills, please seek the help of a professional to perform the installation. Check your packages immediately upon arrival to ensure that everything listed is included, and to check for damage during shipping.
-
Page 2: Important Info
• Undo bolts and keepers on inner fender wells –Photo C IMPORTANT INFO: If your CBI product comes as unpainted, bare steel or alumi- num. You will want to either powder coat or paint prior to final installation, however it is very important to PRE-INSTALL the... - Page 3 • Remove plastic impact bumper –Photo H • Reach in the inner fender and take the bolt out holding the power steering lines –Photo L • Remove aluminum bumper, same 14mm nuts for new bumper install –Photo I • Mount the re-location brackets as shown in photos (5/6” bolts under the A/C condenser factory bolts in factory location) –Photos M&...
- Page 4 • Remove front skid plate • Remove air dams –Photo O • Cut air dams off where shown –Photos Q & R • Cut flare off at bottom of tape, the flare may end up a little long. You can trim it to match the bumper once it has been re- installed.
- Page 5 • Mask the face of the bumper as shown in photos starting at the fog lights, line up the tape with the edge of the opening holding a straight line around the corner and a 1/4” above the point on the bumper at the fender well –Photos X &...