Sanji ZX400 Instructions For Use

ZX300-400-500-USER-REV3
FITMENT CENTRE STAMP:
SANJI SECURITY SYSTEMS (PTY) LTD
106 16TH ST MIDRAND
GAUTENG, SOUTH AFRICA
TEL +27 11 266 7500
FAX +27 11 266 7501
E Mail : sales@sanji.co.za
http://www.sanji.co.za
29) USING YOUR PINCODE OVERRIDE
(ZX400 & 500 ONLY)
The ZX400 and ZX500 can be temporarily overridden by
entering the supplied 5 digit pincode override by means of
turning the ignition switch on and off in a sequence as
per instructions below. If the unit is in immobiliser armed
mode (dash led solid) you can begin to enter your code. If
the alarm is set, open the door and turn the ignition on.
Wait for the unit to stop sounding, turn the ignition off.
You can begin to enter your code.
EXAMPLE
PINCODE
3 1 4 2 1
Digit 1 [number 3]
Turn ignition key on, led will start to flash, on the THIRD
flash, turn ignition key off, the indicators will flash once,
you have now successfully put your first digit in.
Digit 2 [number 1]
Turn ignition key on, led will start to flash, after the
FIRST flash, turn ignition key off, the indicators will flash
once, you have now successfully put your second digit in.
Digit 3 [number 4]
Turn ignition key on, led will start to flash, after the
FOURTH flash, turn ignition key off, the indicators will
flash once, you have now successfully put your third digit
in.
Digit 4 [number 2]
Turn ignition key on, led will start to flash, after the
SECOND flash, turn ignition key off, the indicators will
flash once, you have now successfully put your fourth
digit in.
Digit 5 [number 1]
Turn ignition key on, led will start to flash, after the
FIRST flash, turn ignition key off, the indicators will flash
once, you have now successfully put your fifth digit in
and have successful overridden your vehicle.
If you enter an incorrect digit the unit will not flash the
indicators and will revert back to the first digit. If you
enter an incorrect digit 3 times the unit will sound the
alarm. Turn the ignition on and wait for the unit to stop
sounding. You can now re-enter your code.
*
30) ANTI KEY THEFT KEYPAD
The optional anti key theft keypad protects the vehicle
against theft in the event of key theft or driver mugging.
A personal pin code has to be entered into the keypad
before the vehicle can be driven. The unit will come default
with code 1 1 1 1.
1 2
RESETTING THE IMMOBILISER :
Reset the alarm via your remote control (unlock button),
the alarm dash led will be flashing rapidly. Turn the
ignition on and enter your 4 digit code, the keypad led
will turn on for 5 seconds, the unit will reset the
immobiliser, the alarm dash led will turn off, the vehicle
can now be driven. You can also enter your code before
turning the ignition on however once you have entered
your code you then have 5 seconds to turn the ignition on
in order for the immobiliser to be reset so the vehicle can
be driven.
KEYPAD NUMBERS AND BUTTONS :
When you press any button the unit will beep and the
numbers will light up for 10 seconds. If a door is opened
the keypad numbers will light up.
INCORRECT CODE :
dash led
If an incorrect code is entered the unit will sound a rapid
beep to warn you that the wrong code was entered. You
have 4 attempts to enter your correct code, after the 4th
attempt the unit will lock up for 10 minutes. The unit will
beep and flash the numbers for a 10 minute period to
warn you that the keypad has locked up. During this time
you will be unable to reset your immobiliser.
CHANGING YOUR 4 DIGIT CODE :
Press button 1 and 5 simultaneously until the unit sounds
a long beep.
A) Enter your current 4 digit code, if the correct code is
entered the unit will sound a long beep and enter change
code mode. The keypad led will turn on solid. (If incorrect
code is entered the unit will exit change code mode and
revert back to normal operation).
B)
Enter your new 4 digit code, after the 4th digit is
entered the unit will sound a long beep.
C) Enter your new 4 digit code again as confirmation. If
the 1st code matches the 2nd code, the new code will be
saved, if they don't match the new code will not be saved
and the current code will remain.
31) REMOTE LOW BATTERY WARNING
The remote led will normally be on solid when pressing
any button. If the remote batteries are low the led on your
remote control will flash. Replace the batteries with:
2 x CR1220 lithium batteries.
3 4 5