Datalogic DataVS2 Quick Reference Manual

DataVS2 - VSM
Vision Sensor Monitor

QUICK REFERENCE GUIDE

DESCRIPTION
The VSM is an external monitor compatible with all the vision sensors of the
DataVS2 series. The device displays images, results and statistics of the
check carried-out on the sensor as well as the fine tuning of the configuration
parameters.
-
Monitor with 3.5" colour LCD display;
-
Operator interface with 8 push-buttons
and 8 signalling LEDs;
-
Compatibility with the entire DataVS2
series;
-
Image and statistics visualisation;
-
Configuration parameter modification;
-
Memorisation of 20 different inspections;
-
Different user profiles
through passwords.
FEATURES
VSM MONITOR
The VSM displays the images processed by the DataVS2, manages
inspections and carries-out the parameter fine tuning.
1. Monitor
2. Status LEDs
3. STATUS Button
4. TEACH Button
5. Power Supply
Connector
6. ARROW Buttons
7. Ethernet Network
Connector
8. ESC Button
9. SET Button
10. Power, OUT, ETH
Link LEDs
SIGNALLING LEDS
From left to right
1. Setup Mode, green;
2. Adjust Mode, green;
3. Monitor Mode, green;
4. Main Menu, green;
5. Power Supply, green;
1 2 3 4
6. Digital Output 1, yellow;
7. Digital Output 2, yellow;
8. Connection Status, green.
ELECTRICAL CONNECTIONS
4 3 4
2 1
1
M12 4-Pin Male M12 Reverse Keyed 4-Pin Male
(Power Supply)
pin 1: +24 Vdc
pin 2: Reserved
pin 3: GROUND
pin 4: Reserved
The VSM monitor can be connected in a LAN network using a straight
Ethernet cable or can be connected using a point to point connection directly
to a vision sensor.
LAN CONNECTION
Power
management
DATAVS-CV-RJ45D-03
LAN
POINT-TO-POINT CONNECTION
Power
DATAVS-CV-VSM-xx
GROUND CONNECTION
To comply with the EMC requirements, the Ethernet cable shield has to be
grounded. (Use the yellow/green cable supplied with the VSM).
Ring Nut
Insert the washer M12 on the yellow/green cable in the VSM connector and
then screw the Ethernet cable until the ring nut reaches the washer.
Warnings

Insert the cable into the correct connector following the key
5 6 7 8
indications inside the body
 After inserting the cable, turn the ring nut anticlockwise to ensure
connection

Never force the cable inside the connectors.

Make sure that every cable is connected to the right connector

Before disconnecting the cable, completely turn the ring nut
anticlockwise
3
2
(Ethernet Network)
All the accessories for VSM mounting are included in the package. The VSM
unit can be installed on a DIN rail or on a panel.
pin 1: Ethernet RX+
pin 2: Ethernet TX+
DIN RAIL MOUNTING
pin 3: Ethernet RX-
pin 4: Ethernet TX-
Wedge the VSM unit in the DIN rail. First set the upper part of the monitor and
then press down the lower part.
Once inserted, block the VSM monitor using the two white side locking clips.
PANEL MOUNTING
Place the rubber seal around the monitor body.
Washer M12
Then fix the monitor on the panel using the two locking screws and the two
rubber caps.
Locking
Screws
VSM MOUNTING
Locking Clips
Supply Voltage:
Ripple Voltage:
Current Draw:
Dimensions:
Indicators:
Setup:
Data Retention:
Operating Temperature:
Storage Temperature:
Vibrations:
(EN60068-2-6)
Shock Resistance:
(EN60068-2-27)
Housing Material:
Mechanical Protection:
Connections:
Weight:
Rubber Seal
Cap
R7.5
[R0.30]
92 ±0.2
[3.62 ]
±0.01
Panel Cutout
TECHNICAL DATA
24 Vdc ± 10%
2.4 Vpp max
Max 150 mA @ 24 Vdc
96 x 96 x 39 mm
8 LEDs + 3.5'' LCD color display
DataVS2 GUI
non volatile FLASH memory
-10 °C ... +55 °C
-20 °C ... +70 °C
14 mm @ 2 to 10 Hz;
1.5 mm @ 13 to 55 Hz;
2 g @ 70 to 200 Hz; 2 hours on each axis
11 ms (30 G) 6 shocks on each axis
ABS
IP20 (IP40 when panel mounted)
2 x M12 4-pin
180 g
OVERALL DIMENSIONS
96
[3.78]
45.0
14.0
[1.77]
[0.55]
90.2
[3.55]
96
[3.78]