emaux CE306A Installation And Operation Manual

Parts list
Key NO. Part NO.
1 89050301 Hose weight
2 01112017 Nut
3 01100005 Roller bumper strap
4 89050302 Top Assembly for Tube
5 01010015 Tube
6 89050303 Body with Screws
7 08050017 Automatic Regulator Valve
8 02141005 Flexi Hose Connector
9 02140001 2" Hose Cone
10 89050304 Bottom Assembly for Tube
11 02300002 Flipper
12 01112018 Flipper Cover
13 02300003 Pleated Disc
14 02300001 Interleaver
15 01093008 Hose (Male - Female)
16 01093009 Hose (Female - Female)
15
16
10
11
12
13
14
Product Description
1
2
X12
5
X1
4
QTY
1
1
Fast Start-up, Safely Operate
1
and Efficiently Clean!
1
Installation and Operation Manual
2
1
1. Preparation of Your Pool
1
Before assembling and installing your cleaner, your pool should be
clean and algae-free so as not to inhibit the cleaner's traction. If
1
necessary, make the following preparations before proceeding:
1) Chemically balance the pool water.
1
2) Brush pool and let the debris settle.
3) Hand vacuum thoroughly.
1
4) Clean filter and pump strainer basket.
1
II. Assembly
1 Remove the body and all of its parts from the box and check to
make sure that all components are included. Refer to Figure 1.
1
Components Check List
A) Body
1
B) Nut
C) Hose weight
12
D) Automatic regulator valve
E) 1.5" & 2 " Hose Cone
F) Roller bumper strap
1
G) Pleated Disc
H) Hose-10.4m total length (not shown)
I) Interleaver
A
Figure 1
F
C
B
3
H
4
Step
1) Attach The disc
To install the disc, locate the words "Up" and face them towards the
main body, slip the disc over the Interleaver-(flat side down towards
pool floor)-and full gently until it seats itself on the other side in its
groove as illustrated in Figure
6
2) disc must be installed flat side down, pleated side up. Once in
place, the disc should rotate and turn freely.
The disc is not reversible. The raised pleats on the Pleated Disc must
face upward. The flat side of the disc should face down to rest
against the pool surface.
7
Step 2. Attach The Roller Bumper Strap
Insert the bottom end of the strap into the slot provided on the main
body. Insert the top end of the strap into the locking clip attached to
the swivel head. See Figure 3.
Step 3. Assemble The Hose
8
Twist and push the female ends onto the male ends after dipping the
ends into the pool to wet them. See Figure 4. Continue until you've
connected all the sections you need. After connecting the hose
weights to the hose as described in "Table A", then connect the hose
9
to the cleaner. See Figure 5.
One of the hose sections has 2 female ends and a hose protector.
This section should be fitted last and attached to the pool's vacuum
connection.
CE306A
Your fully assembled the cleaner should look like this.
Figure 2
Pleated Disc
in groove
Figure 3
Figure 4
D
G
Male hose end
E
X12
I
X1
Female hose
Figure 5
Male connection of
the top assembly
should connect to
the female end
of the hose
III. Installation
The cleaner is designed to work in a wide variety of swimming pools.
This is the reason certain items (such as a 2" hose cone and valve
cap for the automatic regulator valve) are included with your
cleaner. These may or may not be needed, depending on the
particular features of your pool.
Both the standard in-skimmer installation and an optional vacuum
line installation are covered in this manual. Check to see which most
closely fits your pool configuration and follow the directions.
1
CE306B CE306C
Main body
Pleats of
Pleated Disc
Locking
Female hose end
Automatic Regulator Valve
Female / female section to be
added last, to the Automatic
Valve Regulator
EMCE15040757