emaux MFS20 User Manual

PARTS FOR FILTER MAX FILTER
Key No. Part No.
1 89010701 Air Release Valve with Oring
2 06021013 Plastic Pressure Gauge with O-ring
3 01201022 Lid (Transparent)
4 03021035 M6 Nut
5 89012512 Clamp Kit
6 01111101 Star-Shaped Nut
7 02010007 O-Ring
8 03011166 M6×110mm Screws
9 89012606 Filter Tank for MFS17
9 89012607 Filter Tank for MFS20
9 89012608 Filter Tank for MFS24
9 89012609 Filter Tank for MFS27A
9 89012620 Filter Tank for MFS27
9 89012610 Filter Tank for MFS31A
9 89012621 Filter Tank for MFS31
9 89012622 Filter Tank for MFS35
10 02011003 O-Ring for 1.5" adaptor
10 02020016 O-Ring for Connector
11 88280811B 6 Way 1.5" Valve with Piping Kit, 1.5" union set x 3 and pressure gauge (Black)
11 88280812B 6 Way 2" Valve with Piping Kit, 2" union set x 3 and pressure gauge (Black)
12 89012601 The Inner Tank System for MFS17
12 89012602 The Inner Tank System for MFS20
12 89012603 The Inner Tank System for MFS24
12 89012604 The Inner Tank System for MFS27A
12 89012605 The Inner Tank System for MFS31A
12 89012617 The Inner Tank System for MFS27
12 89012618 The Inner Tank System for MFS31
12 89012619 The Inner Tank System for MFS35
13* 01172007 Laterals(115mm)
13* 01172008 Laterals (126mm)
13* 01172010 Laterals (185mm)
14 01111059 16-21inch Filter Base
14 01111062 21-28inch Filter Base
14 01112037 31-35inch Filter Base
15 89011601 Water Drain Set
Notes:13* MFS17/ MFS20 should have 8pcs of lateral (115mm)
13* MFS24/ MFS27A/ MFS31A should have 8pcs of lateral (126mm)
13* MFS27/ MFS31/ MFS35 should have 4 pcs of lateral (115mm) and 4pcs of lateral (185mm)
Description
4-4
Qty
FILTER MAX SERIES
1
1
1
1
MODEL: MFS17 / MFS20 / MFS24 / MFS27A / MFS27 /
1
MFS31A / MFS31 / MFS35
1
1
1
1
1
1
1
1
1
Your Emaux "Filter Max" Filter is a high performance corrosion-proof filter that has superior flow characteristics that is with the
1
ease of operation. Everything is made simple from installation, operation to the maintenance of the filter. Your "Filter Max"
1
filter will be your pool filtration partner that provides clear water with the least maintenance hassle and care.
2
WARNING:
2 BEFORE INSTALLATION BE SURE TO READ ALL INSTRUCTIONS AND WARNINGS
1
CAREFULLY. KEEP THIS USER MANUAL FOR FUTURE REFERENCE.
1
HOW IT WORKS
1
The Filter uses special sand to remove dirt particles from pool water. Filter sand is loaded into the filter tank to
1
act as the filtration media. The pool water which contains dirt particles is pumped through your piping system to
1
the filter via the filter control valve. As pool water passes through the filter, dirt particles will be caught by the
1
1 sand bed and filtered out. The cleaned pool water is returned from the bottom of the Filter Tank, through the
1
control valve and back to the pool through your piping system. The entire process is continuous and automatic.
1
It is this process that provides the filtration and circulation of water in your pool.
1
With the filtration process, dirt will accumulate and becomes saturated in the filter tank. Pressure in the tank will
*
increase and the resistance of water flow will occur. This means it is time to clean (backwash) your filter.
*
Another indication to know when to clean (backwash) the filter is by checking the pressure gauge reading.
*
Backwash operation should be performed when the pressure increases by 10psi above the pressure when it was
1
clean. Typically a clean filter will run at 10 to 15psi, so take note of the pressure gauge reading when the filter
1
was installed. When the pressure reaches approximately 20 to 25psi or 50% increase from the clean reading,
1
proceed to the Backwash operation.
1
WARNING: turn off the pump before switching the control valve handle.
To perform the Backwash operation, position the handle on the control valve to "Backwash", the water flow is
automatically reversed through the filter so the water is directed from the bottom of the tank, up through the
sand, flushing the trapped dirt and debris
out of the waste line. The duration of the backwash operation will depends on how dirty your filter is. Check the
sight glass to see when the water becomes clear. It is recommended that the backwash should be at least 2
minutes long.
Once the backwash operation had been completed, the filter should go through the process of "Rinse" and
then back to "Filter". To perform the different operations, position the handle on the control valve as indicated.
INSTALLATION
Installation had been made simple, the only tools needed is a
screwdriver and pipe sealant for plastic.
The filter should be installed as close to the pool as possible, but
keep a distance of at least 5 feet (1.5m). Locate the Filter on rigid,
level surface, preferably in a dry, shaded, and well-ventilated
area. Prior to installation give consideration to the following:
Position of suction, return, and waste connections. Access for
backwashing operation and servicing; protection from sun, rain,
splashing, etc; Drainage of filter room; Ventilation and protection
of the motor.
1)Fill the tank with water to the level that covers the laterals
(crepinas), or about 1/3 of the tank height is recommended.
This will avoid damages to the laterals (crepinas) by the force
of the sand when pouring into the filter.
, , ,
MFS17 MFS20 MFS24 MFS27A
, , ,
MFS27 MFS31A MFS31 MFS35
1. Place on tank
2. Add water to
opening. cover laterals
and add sand.
1-4
EMFI16030555