Page 1
Technical Guide 2009-Plasma HD and FHD TV (12 Generation) Applies to models: TC-P42X1 TC-P50X1 TC-P42S1 TC-P46S1 TC-P50S1 Model TC-P42PX1 Panasonic Service and Technology Company National Training TTG090306CP/090306...
Page 2
National Training "HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.“ Copyright 2009 by Panasonic Service and Technology Company All rights reserved. Unauthorized copying and distribution is a violation of law.
Topics https://www.werbemousepads.de/pdf/ Introduction Series Line-up Features Comparison Technical Changes Standby – Power On Operation Shutdown Circuit Explanation Troubleshooting Boards Isolation Service Notes...
Introduction https://www.werbemousepads.de/pdf/ Panasonic's 2009 line of VIERA HDTVs have improved their energy efficiency vs. last year's models, while also improving the overall picture performance of the HDTVs. This is list of features provided by Panasonic's 2009 line of VIERA HDTVs Access to HD movie rental via Amazon Video-on-Demand.
Z1/V10 Series https://www.werbemousepads.de/pdf/ Z Series The flagship VIERA plasma in 2009 is the Z1 series, with a revolutionary one inch thin panel design and Wireless HD connectivity to deliver the ultimate sleek, uncluttered HDTV viewing experience. VIERA CAST web menu with the new streaming HD movie rental capability via Amazon Video-on- Demand.
G10/S1 Series https://www.werbemousepads.de/pdf/ G10 Series The VIERA G10 features the VIERA CAST web menu. THX certified Display. 1080p resolution, deeper blacks, improved native contrast ratio of 40,000:1, Full-Time 1080 TV lines of motion resolution, an Infinite Black panel, 600Hz Sub-field Drive, as well as Game Mode and VIERA Link.
X Series https://www.werbemousepads.de/pdf/ X1 Series The X1 VIERA HDTVs offer a 600Hz Sub-field Drive that delivers razor-sharp motion focus. VIERA Image Viewer for photos playback. VIERA Link control of all compatible A/V home entertainment components via a single remote. Improved native contrast ratio of 30,000:1, an Infinite Black panel, and a Game Mode. Available in a 50-inch class and 42-inch class.
New Features Comparison https://www.werbemousepads.de/pdf/ Feature Wireless HD RF Remote Control RS232 PC input LAN Port Viera Cast Viera Link With Network Camera AVCHD/MPEG2/JPEG playback Thru SD Card 1080 Lines Moving Picture Resolution 900 Lines Moving Picture Resolution 720 Lines Moving Picture Resolution...
Power Consumption Comparison https://www.werbemousepads.de/pdf/ 2008 LCD 2008 Plasma 2009 Plasma TC-32LX85U TH-42PX80U (No Fans) TC-P42X1 (No Fans) Power Consumption Power Consumption Power Consumption Maximum Maximum Maximum Standby condition 0.6 W Standby condition 0.3 W Standby condition 0.3 W Weight 35.3 lb.
Moving Picture Resolution 1080 Lines https://www.werbemousepads.de/pdf/ with 600 Hz Sub-field Drive Sports and other fast-action scenes are stunningly clear. To improve the moving picture resolution, frames are generated at the sub-field level. With a frame generated each 1/60th of a second, images are created to match the motion.
Moving Picture Resolution 900 lines or more The resolution can be different between static versus dynamic. As you are watching moving images - that is the resolution that Panasonic quotes. It might be 1300 for a JPEG (just showing a comparison) 480 Hz Sub-field Drive 480Hz refers to the subfield drive.
Sub-field https://www.werbemousepads.de/pdf/ A number of sub-fields overlap to depict the image in each frame. Panasonic technology detects movement in the image and reflects it in each individual sub- field to achieve smooth playback with minimal blurring. What's Sub-field? Plasma TVs express a single frame of an image by using multiple images, each having a different gradation.
Over 2,000,000:1 High Contrast (Native 40,000:1) https://www.werbemousepads.de/pdf/ Series Z1, V10, G15, G10, S1, The shading in dimly-lit night scenes is beautifully rendered. A high contrast is achieved by NeoPDP technology. This newly developed, highly efficient panel creates a larger difference between maximum brightness (white) and minimum brightness (black).
AR Filter https://www.werbemousepads.de/pdf/ Enjoy clearer images without bothersome reflections. Screen reflections are cut when viewing in bright rooms. This filter minimizes light reflections. Panasonic's unique low-reflection filter greatly reduces the reflected light intensity compared with the incident light intensity.
Wireless HD™ https://www.werbemousepads.de/pdf/ View HD images with wireless operation. This function sends high-resolution, full-HD data over a wireless connection. It enables a flexible VIERA layout to match any room interior. *A special receiver is required to use WirelessHD™. The usage distance and installation environment for the Wireless HD™ System and the effect that other machines will have on it are presently being tested, and the system performance is being confirmed.
Radio Frequency Remote Control https://www.werbemousepads.de/pdf/ The signals that propagate all around the room can be used to operate equipment without having to worry about the direction that the remote control is pointed. This allows easy operation of a Tuner that is placed inside an AV rack. Note: This remote control uses 2.4GHz frequency.
TC-P42X1 (HD Model) Connection between Connection between https://www.werbemousepads.de/pdf/ No LED the SC board and the the SC board and the on the SS SS board (SC3-SS3) SS board board No STB5V jumper on the SS board A board location...
Technical Changes (TC-P42X1) https://www.werbemousepads.de/pdf/ No D board These circuits are now No SD Card Slot board (GS) part of the A board No Fan Drive board (PB) The A board is now located below the SS board. SS11 besides providing Vsus to the SS board, now it also provides P15V ...
Boards Description https://www.werbemousepads.de/pdf/ Board Description Board Description Speaker out, Sound Processor, AV Terminal, AV Switch, DC-DC Converter, Digital Signal Processor, Microcomputer, HDMI Interface, Peaks Lite 2, Full Power Supply HD, (Newly Added SD Card Slot, Fan Control, Format Converter, Plasma AI, Sub-Field Processor) Data Driver (Right) Power Switch Data Driver (Left)
Standby Circuit Operation https://www.werbemousepads.de/pdf/ When the TV is plugged in: AC is applied to the standby circuit in the power supply to produce STB5V. The STB5V is provided to the A board via connectors P7 (Pin 5) and P25 (Pin 9). Connector P25 is connected to connector A25 on the A board and connectors P6 and P7 are both connected to connector A6 on the A board.
Power On Operation https://www.werbemousepads.de/pdf/ The power command from the power switch on the S board or the remote control receiver on the K board is provided to the Main CPU on the A board (IC1100) thru connector A1. The CPU on the A board outputs the “TV_SUB_ON”...
Sub-Voltages Distribution https://www.werbemousepads.de/pdf/ On previous generations these voltages were present for approximately 15 seconds after connecting the TV to the AC line. This does not apply to this year’s models. These voltages are called sub-voltages and they are only used by the A board. The sub-voltages are developed when the power is turned on.
10 blinks Condition Troubleshooting https://www.werbemousepads.de/pdf/ Since the Sub voltages are only present after the power has been turned on, there will not be a 10 blinks condition at plug-in for the 2009 models. These 3 conditions can cause the TV to shutdown and the power LED to blink 10 times Missing/Shorted F_STB_15V, SUB9V, SUB5V, and BT30V Wrong diagnostic by the A board Note:...
https://www.werbemousepads.de/pdf/ SOS Detect (Shutdown) When an abnormality occurs in the unit, the “SOS Detect” circuit is triggered and the TV shuts down. The power LED on the front panel will flash a pattern indicating the circuit that has failed. If the power LED continues to blink even after the TV is unplugged, press and hold the power switch on the TV for a few seconds until the LED turns off.
Panel MPU SOS Detect https://www.werbemousepads.de/pdf/ • Protection circuits are incorporated in the unit to prevent the failure of a single circuit or component from creating catastrophic damage. • A shutdown condition occurs when there is an over voltage, a short or a drop in any of the voltage lines.
65. As a result, the unit shuts down and the power LED blinks 6 times. The TC-P42X1 series monitors the sustain board output. This signal is connected to the recovery circuit in the SC board. Any abnormality on the sustain board will trigger the 6 blinks code.
System MPU SOS Detect https://www.werbemousepads.de/pdf/ 10 Blinks SOS: IC5401 generates the SUB9V, IC5607 generates the SUB5V, and IC5480 generates the BT30V. The SUB9V, BT30V, and SUB5V from these ICs are monitored by IC1100. Any abnormality on these voltages (Including the F_STB15V), triggers the shutdown circuit and the MPU shuts down the unit.
2 Blinks Error Code https://www.werbemousepads.de/pdf/ These 3 conditions can cause the TV to shutdown and the power LED to blink 2 times Missing P15V A short of the P15V Wrong diagnostic by the A board...
Troubleshooting 2 Blinks Error Code https://www.werbemousepads.de/pdf/ When troubleshooting a PDP TV that is shutting down and the power LED blinks 2 times: Find out if 15V is output at pin 1 of connector P6 of the P board. If 15V is present, it’s likely that the A board is defective.
3 Blinks/4 Blinks Error Code https://www.werbemousepads.de/pdf/ 3 Blinks Error Code Since the IC (IC9805) that generates the monitored 3.3V for 3 blinks condition and the IC (IC9003) that detects this condition are both located on the A board, then the A board is the only suspect when the TV shuts down and the power LED blinks 3 times.
5 Blinks Error Code https://www.werbemousepads.de/pdf/ These 4 conditions can cause the TV to shut down and the power LED to blink 5 times Missing P5V A short of the P5V A short of the Vda line (Note: missing Vda from the P board does not cause 5 blinks) Wrong diagnostic by the A board...
Troubleshooting a 5 Blinks Error Code https://www.werbemousepads.de/pdf/ When troubleshooting a PDP TV that is shutting down and the power LED blinks 5 times: Find out if pins 1 or 2 of connector P35 are shorted to ground. If shorted, possibly the panel is bad. If there is no short circuit, proceed to check the P5V line.
6 Blinks Error Code (TC-P42S1) https://www.werbemousepads.de/pdf/ The Scan and Sustain voltages on the SC and SS boards are monitored by an SOS Detect circuit. The energy recovery circuit in the SC board is monitored by a comparator (Error detect IC16581). The output voltage is compared to 2 reference voltages derived from the P15V.
6 Blinks Error Code Circuit Explanation https://www.werbemousepads.de/pdf/ The sustain drive circuit on the sustain board is not a complete circuit. There is a part of this circuit in the SC board. The cable between connector SS3 on the sustain board and SC3 on the scan board links these 2 circuits The section of the sustain drive circuit located on the scan board uses Vsus for complete operation of the sustain output circuit.
Driver Reset Circuit Operation https://www.werbemousepads.de/pdf/ The DRV RST circuit of the A board is used to monitor the physical connection of the A board to the C board. DRV RST input to IC9500 and IC9003 must be high for the unit to operate. The A board provides the 5V source needed to power the C boards.
7 Blinks Error Code https://www.werbemousepads.de/pdf/ The SC board has 2 SOS detect circuits, energy recovery and floating ground section. When the energy recovery circuit is triggered, the TV shuts down and the power LED blinks 6 times. The floating ground circuit monitors the scan circuit output, the 15V_F, the scan_pro, Vscan, and the physical connection between the SC board and the SU/SD board (CHA).
8 Blinks Error Code Circuit Explanation https://www.werbemousepads.de/pdf/ There is an extra SOS Detect circuit in the Sustain board. This circuit is used to monitor for physical connection between the panel and the SS board. Under normal condition, Q16280 is on. When Q16280 is on, a low is provided to the anode of D16280 (D280).
8 Blinks Error Code (TC-P42X1) Circuit Explanation https://www.werbemousepads.de/pdf/ On this model, only the circuit used to monitor for physical connection between the panel and the SS board is used to trigger an 8 blinks condition. The energy-recovery- circuit portion used to monitor the operation of the sustain drive circuit is located on the SC board.
11 Blinks Circuit Explanation https://www.werbemousepads.de/pdf/ The ventilation fans are monitored to be sure they are operating properly. If one of the fans stops or its resistance increases, the resulting current change is applied to pin 36 of the main CPU. The fan drive circuit is located in the A board.
https://www.werbemousepads.de/pdf/ Boards Isolation Procedure Caution: Do not let the TV run for more than 30 seconds while connectors or boards are disconnected.
SC Board Isolation Procedure (TC-P42S1) https://www.werbemousepads.de/pdf/ When the SC board is suspected to be the cause of a 6 or 7 blinks condition, it can be isolated for confirmation. To isolate the Scan Drive Section (SC, SU, and SD board), remove connectors SC2 (Vsus) and SC20 (P+15V, P+5V, and scan pulses) from the SC board and connector SS33 from the sustain board.
SS Board Isolation Procedure (TC-P42S1) https://www.werbemousepads.de/pdf/ To determine if the Sustain board is causing a 8 blinks condition: Unplug connector SS11 and connector SS33. Press the power switch. If the TV no longer blinks 8 times, then the SS board is defective.
SS Board Isolation Procedure (TC-P42X1) https://www.werbemousepads.de/pdf/ To determine if the Sustain board is causing a 8 blinks condition: Unplug connector SS23. Press the power switch. If the TV no longer blinks 8 times, then the SS board is defective. Note 2: In order to get to SS23, the A board has to be removed.
SU and SD Boards Isolation Procedure https://www.werbemousepads.de/pdf/ Beginning last year (2008), the new plasma models are now designed not to turn- on if either the SU or SD board is disconnected. Disconnecting either causes the unit to shutdown and the power LED to blink 7 times.
SU Board Isolation https://www.werbemousepads.de/pdf/ The 2008 and 2009 plasma models are now designed not to turn-on if either the SU or SD board is disconnected. Disconnecting either causes the unit to shutdown and the power LED to blink 7 times. Unplugging SC41/SU41, SU11/SD11, and SC42/SD42, opens the interlocked connection between VF_GND and CHA on the SC board.
SD Board Isolation https://www.werbemousepads.de/pdf/ The 2008 and 2009 plasma models are now designed not to turn-on if either the SU or SD board is disconnected. Disconnecting either causes the unit to shutdown and the power LED to blink 7 times. Unplugging SC41/SU41, SU11/SD11, and SC42/SD42, opens the interlocked connection between VF_GND and CHA on the SC board.
Signal Process Explanation https://www.werbemousepads.de/pdf/ The main function of the A board is to select and process one of the incoming video signals. Video inputs 1 and 2, Component Video Inputs 1 and 2, PC input, and the composite video output of the tuner are all are connected to IC3001 for selection. The video output signal of the switch can be in any of the three formats: Video, Y/C, or Y, Pb, Pr.
Service Mode https://www.werbemousepads.de/pdf/ While pressing [VOLUME ( - )] button of the main unit, press [INFO] button of the remote control three times within 2 seconds. Key command [1] button...Main items Selection in forward direction [2] button...Main items Selection in reverse direction [3] button...Sub items Selection in forward direction [4] button...Sub items Selection in reverse direction [VOL] button...Value of sub items change in forward...
Self Check https://www.werbemousepads.de/pdf/ 1. Checks the communication IIC bus lines 2. Provides a SOS History To Access the Self-Check Mode, turn the TV on and while pressing To Access the Self-Check Mode, turn the TV on and while pressing “VOLUME ( - )” button on the main unit, press the “OK” button on the “VOLUME ( - )”...
Reset Procedure https://www.werbemousepads.de/pdf/ Note: All customer programmed parameters will be erased. Reset forces the TV to factory shipment setting. To reset the Press and hold the “VOLUME ( - )”button on the TV and press the “MENU” button on the remote control for more than 3 seconds. To Exit: Disconnect the AC cord from wall outlet.
Glossary https://www.werbemousepads.de/pdf/ Resolution Resolution is a combination of values that express the quality of displayed images. A display's resolution is indicated by the number of dots in the horizontal and vertical directions of the screen, such as 1024 x 768 dots. Higher values indicate clearer, sharper image reproduction. The larger the screen size, the higher the required resolution.
Page 75
Glossary https://www.werbemousepads.de/pdf/ THX is a trade name of a high-fidelity sound reproduction standard for movie theaters, screening rooms, home theaters, computer speakers, gaming consoles, and car audio systems. THX stands for Tomlinson Holman's eXperiment. The THX system is not a recording technology, and it does not specify a sound recording format: all sound formats, whether digital (Dolby Digital, SDDS) or analog (Dolby Stereo, Ultra-Stereo), can be "shown in THX."...
Page 76
Glossary https://www.werbemousepads.de/pdf/ Is The color encoding system used for analog television worldwide (NTSC, PAL and SECAM). The YUV color space differs from RGB, which is what the camera captures and what humans view. Composite Video and S-video The original TV standard combined luma (Y) and both color signals (B-Y, R-Y) into one channel, which uses one cable and is known as "composite video."...
Page 77
https://www.werbemousepads.de/pdf/ The End...