Konica Minolta RA-121 Instruction Manual

How to Use
Before Use [Make sure to read]
CAUTION
 Before using the dolly, check each of the connecting part for looseness. If any part is loose, re-tighten it securely.
 If any parts have problems such as a crack or large bend, do not use them. Please contact a KONICA MINOLTA-
authorized service facility.
 Use the dolly on a level, flat, firm floor. Using this stand set on an uneven or sloped floor may make this stand set unstable.
 Before moving the tripod, be sure to dismount the RANGE7 unit. If the tripod is moved with RANGE7 mounted, it may
overturn, causing injury or damage to the equipment.
 Do not lean against the tripod or platform.
 If any abnormality is found (any movable part cannot smoothly work), contact a KONICA MINOLTA-authorized service facility.
 If any part of the dolly is lost or damaged, do not use a commercially available part as a substitute. Please contact a
KONICA MINOLTA-authorized service facility. Using a commercially available part as a substitute may result in damage
to the equipment or injury due to insufficient strength.
Adjusting the RANGE7 Position [How to Operate the Tripod Platform]
The platform enables horizontal, vertical, and swing adjustment. Operate each lever to adjust the RANGE7
position.
Note
 Before changing the RANGE 7 position, check that there is no one nor any materials around the platform that may get hit.
 Excessively tightening the pan lock knob, tilt lock lever and swing angle adjusting lever result in damage to the equipment.
 Be careful not to get fingers caught in the tilt section of the platform. Keep fingers away from this area.
 When changing the tilt direction of the RANGE7, be sure to lock the pan and swing positions first. In addition, when
changing the pan or swing direction, lock the tilt position first.
RANGE7 Swing angle
adjusting lever
Pan lock knob Tilt lock lever
This figure shows an example
of the configuration using
the dolly. The Dolly VI-B41 is
optionally available.
Pan lock knob
(Horizontal adjustment)
Loosen the pan lock knob
to adjust horizontally.
Loosen
Tighten
Tilt lock lever
(Vertical
adjustment)
Loosen the tilt lock
lever to adjust
vertically.
Tighten
Loosen
Tighten
Swing angle
Loosen
adjusting lever
(Swing adjustment)
Loosen the swing
angle adjusting lever
to adjust the swing
direction.
Tripod Set RA-121/
Tripod Platform Set RA-151 Instruction Manual
The RA-121 tripod set is used for non-contact 3D digitizer RANGE7.
The tripod platform set RA-151 is used to mount the tripod platform on an existing tripod.
The RANGE7 can be mounted to this tripod set.
CAUTIONS DURING ASSEMBLY
 The tripod set RA-121 includes heavy components. Be careful not to catch your fingers between the parts or injure your toes
by dropping such parts.
 Do not take a forced posture during assembly.
 Perform assembly in a sufficiently large space. Leaning parts against a wall, etc. may result in such parts falling over.
Composition of Tripod Set RA-121
The tripod set RA-121 is composed of the tripod platform set and the tripod.
These components are supplied in separate packages. Before using RA-121, you must assemble these components. The
tripod set RA-121 can be used in combination with the Dolly VI-B41 (optional accessory).
Tripod set RA121
Tripod platform set RA-151
Tripod platform set Assembly tool Cable clamp set
Part Names (Complete Assembly Drawing)
* This figure shows an example of configuration using the dolly.
The Dolly VI-B41 is optionally available.
Swing plate
Pan lock knob
Tripod level
Elevator up/
down lever
AC adapter holder
Tripod fixing screw
Dolly
* The Dolly VI-B41 is optionally available.
9222-A0V8-19
Optional accessory
Tripod AC adapter holder Dolly VI-B41
Assembling of the Platform Set
Mounting the swing angle
adjusting lever
Swing angle
adjusting lever
(1) Remove the black cap being
careful not to drop the washer.
Platform
Tilt lock lever
Washer
Elevator
(2) Insert the threaded end of the lever into the
swing angle adjusting lever mounting hole,
Tripod
and mount the lever by turning it clockwise.
Stay
Swing angle adjusting
lever mounting hole
Tripod fixing knob
Washer
Tripod support
Dolly caster
lock
Attaching the cable clamps
Caster
Dolly fixing
lever
Black cap
Cable
clamps
BDECEE