VISUALINT VI-3000-DOM-S-WH Quick Start Manual

Installing the Bullet
lock camera
camera shell rear cover nut base
rubber
gasket
waterproof lock
set screw
Loosen (but do not remove) the set screw on the
side of the camera. Remove the camera assembly
from the base. Remove the rear cover. Open the
waterproof lock and remove the lock nut and
rubber gasket.
rear cover waterproof
— 9 —
Attaching to a Mini Maxx NVR
Plug the camera cable into the Mini Maxx NVR's
PoE port.
From the NVR's main page, click on the
configuration tab.
Navigate to Channels > PoE
Power Information.
Click the checkbox next to
the channel into which you
plugged the camera, then
press the Enable button at the
bottom of the screen.
If your camera is plugged
into the NVR via an external PoE switch, click
the camera in the list of IP device shown in the
top window, then check the appropriate channel's
checkbox and press Enable.
— 12 —
camera base wall anchor
waterproof
lock
screw
Using the adhesive template, drill 4.5mm holes
for the wall anchors (marked B on the template).
If needed, drill a hole for the cabling (marked A).
If the cabling will run along the wall, mount the
lock
camera to a junction box.
If mounting on a pole, slip the straps through
the slits on each side of the base.
Slide the cabling through the rubber gasket and
the waterproof lock.
Insert the wall anchors, then place the camera
base in place and secure with screws.
— 10 —
Attaching to a Line NVR
Download the Visualint IP Finder utility from the
product page's support tab at SnapAV.com.
Install and run the utility to locate the camera.
Once the camera is located, select the camera
by clicking the checkbox to the left of its entry.
Then edit the camera's IP address, subnet mask,
gateway and DNS to the settings desired for that
camera. Press the Batch Modify IP button and the
utility will change the settings and set the camera
to static.
— 13 —
Connect the network cable. If you are not using
POE, connect the power line.
Reattach the rear cover. Insert the rubber gasket
into the waterproof lock. Ensure the cabling is
wall
reasonably taut, then tighten the lock to create a
good seal.
lock nut
level 360°
set screw
Attach the camera to the base by aligning the
unlocked icons on the housing and base, then
twisting until the locked icons align. Adjust the
camera's aim, then tighten the set screw and lock
nut.
— 11 —
That done, go to the NVR's main page, then
click on the configuration tab.
Navigate to Channels > PoE Power Information.
Click on the checkbox for the channel you want
the camera to be, then press the Modify button.
Enter the camera's IP address and its username
and password. Leave all other items at their default
values.
Click the Enable button at the bottom of the
screen, and the NVR should pull all needed info
from your camera and start displaying its feed.
— 14 —
tilt 75°
VI-3000 Series

Quick Start Guide

rotate 360°
VI-3000-BUL-S-WH
VI-3000-DOM-S-WH
Support
For help, email TechSupport@SnapAV.com.
Information, instructional videos, support
documentation, or ideas, visit our website.
3-Year Limited Warranty
This Luma Surveillance™ product has a 3-Year
Limited Warranty. This warranty includes parts
and labor repairs on all components found to
be defective in material or workmanship under
normal conditions of use. This warranty shall
not apply to products that have been abused,
modified or disassembled. Products to be repaired
under this warranty must be returned to a
designated service center with an assigned return
authorization (RA) number. Contact technical
support for an RA number.
Copyright ©2016–2017 by SnapAV. All rights
reserved. Visualint, SnapAV, and all related
marks and images are trademarks or registered
trademarks of SnapAV.
Version 171024-1400
Visualint
— 15 —