Neteon EH2305-1Fm Hardware Installation Manual

Industrial DIN-Rail Unmanaged Ethernet Switch
5/6/8-port Industrial Unmanaged Ethernet Switch
Hardware Installation Guide
Version 1.4
Updated on March, 2012
Introduction
Thank you for purchasing Atop EH-series Industrial Ethernet Switch.
This document intends to provide customers with brief descriptions about
the product and to assist our customers to get started using our devices.
Inside the Package
- Main Product
One EH2305-1Fm, EH2305-1Fs, EH2306 or EH2308 device
■
- Standard Accessories
Terminal block for power input
■
The hardcopy of EH-series Hardware Installation Guide
■
- Optional Accessories
US315-12(US), AC100V~240V 50/60HZ 12V/1.25A, US Plug (optional)
■
→ Atop PN:50500151120009G
US315-12(EU), AC100V~240V 50/60HZ 12V/1.25A, EU Plug (optional)
■
→ Atop PN:50500151120019G

Product Description

EH2305-1Fm
P1 P2 Fault
5-Port Unmanaged Fast Ethernet Switch
with Multi-mode Optical Fiber F.G.
V-
4 ports of 10/100Base-TX with RJ-45 connector
P1
■
V+
1 port of 100Base-FX Multi-mode Optical Fiber
■
with ST connector
F.G.
V-
P2
V+
3
P1 P2 Fault Data Link
F.G.
V-
P1
Rx
1
V+
5
Tx
F.G.
V-
P2
45.4mm
V+
3 4
EH2305-1Fs
5-Port Unmanaged Fast Ethernet Switch
1 2 with Single-mode Optical Fiber
4 ports of 10/100Base-TX with RJ-45 connector
■
1 port of 100Base-FX Single-mode Optical Fiber
■
with SC connector
45.4mm
EH2306
6-Port Unmanaged Fast Ethernet Switch
6 ports of 10/100Base-TX with RJ-45 connector
■
P2 P1
V+ V- V+ V- F.G.
P2 P1
7 8
5 6
3 4
EH2308
1 2
Data Link
8-Port Unmanaged Fast Ethernet Switch
8 ports of 10/100Base-TX with RJ-45 connector
■
Rx
45.4mm
5
Tx

Hardware Installation

Step1: Installation on "DIN-Rail"
All EH23xx Switches are equipped with a DIN-Rail bracket attached
■
4
onto the rear panel. Please follow the below steps to fasten the
switch to the DIN-Rail correctly.
Tip the switch forward and press it against the DIN-Rail after align
■
the bracket springs to the DIN-Rail.
2
Press the bracket against the upper ledge of the DIN-Rail until it
■
clicks.
Notice :
The EH23xx series switch is designed to be mounted on a
well-grounded place, such as a metal panel.
Step2: Connecting the Power
P1 P2 Fault
Prepare the suitable power source and connect it into EH Switch
■
by Terminal Blocks (TB3/TB5).
F.G.
DC 9-30V for EH2305-1Fm, EH2305-1Fs and EH2306 switch
V-
P1 6
■
V+ products.
DC 9-48V for EH2308 switch product.
■
F.G.
You can connect two DC inputs for EH switch power if auto-backup
■
V-
P2 5
needed.
V+
Check P1/P2 power LED. The LED(s) will be lighted when the
■
device is ready.
3 4
3-pin Terminal Block for Power Input
1 2
Pin V+
Signal
DC9-30V
45.4mm
5-pin Terminal Block for Power Input
Pin V+
Signal
DC9-48V
Warning:
Before connecting EH23xx to the DC power input, please make sure
the DC voltage supplied by the power source is correct and stable.
Step3: Connecting the Network Devices
Connect your devices using standard UTP/STP cable with RJ-45
■
connectors to EH switch. (For the cable wiring diagrams, please
refer to section 7)
The corresponding RJ-45 or Fiber SC/ST LED will be lighted if the
■
Ethernet connection is linked successfully.
The LED will be blinked during data transfer by EH switch.
■
※UL Notice for Power supplier
All the series of EH products are intended to be supplied by a Listed
Power Unit marked with "LPS", "Limited Power Source" or "Class 2"
with output rate 9-30VDC 0.6A for EH2305-1Fm, EH2305-1Fs and
EH2306; 9-48V 0.35A(max) for EH2308.
Or, use the recommended power supplies in "Optional Accessories".
F.G.
V-
V+
V- F.G.
0V Frame Ground
P2 P1
V+ V- V+ V- F.G.
V- F.G.
0V Frame Ground