Leader Light LL36 085 User Manual

LL STAGE 6-24D W/RGBA
LL36 085 LL36 095
LL76 085 LL76 095
COMPLIMENTS ON YOUR PURCHASE!
All dimensions are in millimeters
600
98
Package includes:
1. Version without Vario optic 2. Version with Vario optic
- LL STAGE 6-24D with adj. bracket 1pc. - LL STAGE 6-24D with adj. bracket
- PowerCon type "A" + "B" 1pc. - LL VARIO OPTIC STAGE 6 15°
-

User manual

1pc. - PowerCon type "A" + "B"
- User manual
Additional items needed:
- Data cables with XLR 5pin F/M 1pc.
- Controller compatible with DMX 1pc.
- Mounting accessories as necessary
Content:
01 SAFETY INFORMATION
01.1 Risk of eyes damage
01.2 Safety instructions
01.3 Fire protection
02 PRODUCT SPECIFICATION
02.1 Technical specification
02.2 Product description
03 INSTALLATION
03.1 Unpacking
03.2 Physical installation
03.3 Connection
03.4 Control data connection
03.5 DMX channels
04 MAINTENANCE AND SERVICE
ENVIRONMENTAL PROTECTION
Do not throw away the appliance with the normal household waste at the end of its
life, but hand it in at an official collection point for recycling. By doing this, you help to
preserve the environment.
©MMXI - LEADER LIGHT – All right reserved
01 SAFETY INFORMATION
LEADER LIGHT s.r.o.
M.Gorkeho 33
052 01 Spisska Nova Ves
Slovakia
WARNING!!!
www.leaderlight.eu
Carefully read before installing, powering or servicing. Nothing to do if
anything misunderstand! Installation can be done only by a qualified
USER MANUAL
professional in accordance with relevant local codes.
01.1 Risk of eyes damage
- Do not look directly into LED lamps.
- Do not look into light beam from a distance of less than 40 cm (16 inches)!
01.2 Safety instructions
- Shut down power before installation or maintenance.
- Do not modify, alter, or attempt to service the LEADER LIGHT appliance. Doing
so will void the warranty.
- Appliance and recommended AC power supply must be installed by a qualified
professional in accordance with relevant local codes. Use only acceptable source
of AC power and frequency that complies with local biulding and electrical codes.
- Use only the recommended voltage source.
- Appliance always connect to earth (eltech.)!
268
- Do not use or do not connect the products if the power cable, power plug or
fixtures are any way damaged, wet, or if they are overheating.
- Before removing or installing any cover or part of appliance disconnect it from AC
power.
- AC power supply must be protected against overvoltage and short circuits.
1pc.
1pc.
1pc.
01.3 Fire protection
1pc.
- Follow all safety restrictions.
- Thermostatic switches or fuses never to bypass.
- Device never shield. Around the axis of the fitting (180°) must be maintained space
for cooling. Minimum distance from the surrounding objects must be 100mm (4 in.).
- LEDs never direct cover with filters or other materials.
- Allowing max. ambient temperature is 40°C (104°F).
- Luminaries never use without mounting brackets. The housing never install
directly to the surface.
!
02 PRODUCT SPECIFICATION
02.1 Technical specification
Power connection: 100-260V AC 50-60Hz In/Out PowerCon
IP: IP20
Control data: DMX 512 In/Out with XLR 5pin
Ambient temp. (Ta): Maximum 40°C
Net weight: 6kg
Installation: Surface mounting
!
Edition: A - 2011
02.2 Product description
!
Power In DMX In
PowerCon XLR-5pin
Power In Data In
Indication of control LEDs (LED power- green,LED data - yellow)
LED Indication
LED Power blinking - 2Hz
LED Data not lit
LED Data blinking - 4Hz
LED Data fast blinking
LED Power &
alternating blinking
LED Data
03 INSTALLATION
03.1 Unpacking
- Unpack carefully.
- This is electronic equipment and should be handled carefully.
- Damaged delivered package or if are any mechanical parts broken – it must be
claim immediately by the transport company. Photo pictures as evidence are
valuable for future claim.
03.2 Physical installation
- Loading capacity of bearing area has to be at least 10 times the weight of all
device clusters.
- Hairbreadth from combustible materials is 0,5m.
- Before physical installation insert the optic modul on front of luminary. The optic
installation is easy and fast by 2 screws. (figures Nr. 3.1 to 3.2)
03.3 Connection
- Respect all SAFETY INFORMATION 01!
- Connect the ground (earth) !
- It is not necessary to open the fixture before power supply. Power supply is
solved simple with Neutrik PowerCon connectors.
- The fixture is equipped with auto-switching power supply that automatically
adjusts to any 50-60Hz AC power source from 100-260V.
Symbol
- Cord plug connections:
L
N
Page  /2
DMX Out Power Out
XLR-5pin PowerCon
Data Out Power Out
Status
O.K. - Device is working correct
No DMX signal
O.K. - Correct DMX signal
ERROR - Incorrect digital signal
function AutoTest
!
Pin Wire Colour Screw (US)
live brown yellow or brass
neutral blue silver
ground (earth) yellow/green green
Additional information on support@leaderlight.sk