Advertisement
Quick Links
CXR2000/CXR3000 CompletePBX: Getting Started Guide
Package Contents
CXR2000/CXR3000 (2U 19'' width unit)
Power cord
Prerequisites
You need a computer equipped with an Internet browser. Firefox is recommended. By default, the
CXR2000/CXR3000 will get its IP address from your DHCP server. To check the IP address or to
set the CXR2000/CXR3000 static IP address you will need to connect a keyboard and a display to
the CXR2000/CXR3000.
Step 1: Powering Up the Unit
1. For safety reasons, if the line wiring exits the building, it is essential to ground the unit.
Note: Not properly grounding this device will void your warranty!
a. Connect a grounding tab to the grounding screw on the rear panel.
b. Using 12-16 gauge wire, connect the grounding tab to a reliable ground.
Grounding
screw
Power Supply
Figure 1: Grounding Screw on CXR2000 Rear Panel
Grounding
screw
Power Supply
Figure 2: Grounding Screw on CXR3000 Rear Panel
2. Connect a keyboard and a VGA/SVGA screen.
3. Connect the unit to the LAN.
4. Connect the power cord to the device and turn on the power using the switch on the rear panel.
The device startup process takes about 2 minutes. The startup time depends on the number of
telephony ports installed in your CXR2000/CXR3000 unit.
Step 2: Submit Warranty Activation Request
At this point activate the product warranty (a pre-requisite for submitting any request for technical
support). Go to https://xorcom.com/xorcom-product-warranty, complete and submit the form found
there.
PM0616.05 - CXR2000/CXR3000 CompletePBX Getting Started Guide (electronic version)
Misgav Industrial Park, POB 60, D.N. Misgav 20174, Israel
Tel: +972-4-9951999; Fax: +972-4-9990287
Support hardware for 19'' cabinet
CompletePBX software preinstalled on
the hardware
IPMI
Eth0
Eth1
Page 1 of 5
Advertisement
Related Manuals for Xorcom CXR2000
Summary of Contents for Xorcom CXR2000
-
Page 1: Package Contents
You need a computer equipped with an Internet browser. Firefox is recommended. By default, the CXR2000/CXR3000 will get its IP address from your DHCP server. To check the IP address or to set the CXR2000/CXR3000 static IP address you will need to connect a keyboard and a display to the CXR2000/CXR3000. - Page 2 Tel: +972-4-9951999; Fax: +972-4-9990287 Step 3: Configure or Get the IP Settings for CXR2000/CXR3000 If you have a DHCP server: The CXR2000/CXR3000 will get the IP address from the DHCP server. To get the IP address: 1. Login to the CXR2000/CXR3000: a.
- Page 3 Use the Admin|Security|Firewall and Admin|Security|Intrusion Detection dialogs to modify the internal firewall and intrusion detection settings. Unit Status LED (Light Emitting Diode) indicators The CXR2000/CXR3000 is equipped with varying LED indicators on the front panel, depending on the model. Digital CXR2000/CXR3000 Models These are models that have at least one digital PSTN port –...
- Page 4 Port Status LED (Light Emitting Diode) Indicators The CXR2000/CXR3000 has a single green LED status indicator for analog ports (Fig. 4). The Red LEDs are NOT USED for line status indication), and there are two LED indicators for digital ports.
- Page 5 Scan the QR code on the front panel of the IP-PBX for easy access to all relevant product info for this specific product, including detailed technical documentation, “how to” videos, and more. PM0616.05 - CXR2000/CXR3000 CompletePBX Getting Started Guide (electronic version) Page 5 of 5...