Subscribe to Our Youtube Channel
Summary of Contents for Nokeval Ovazone-Core-T-RH-BARO-LUX
- Page 1 Ovazone-Core-Node-T… Ovazone-Core-Router Manual ID7724 V9 20.9.2016 Firmware 1.0-1.2...
-
Page 2: Table Of Contents
Contents Introduction ..............................3 Installation ..............................4 Usage ................................9 Maintenance ..............................9 Specifications ..............................10 Warnings ................................ 12 Manufacturer ..............................12 2 - Introduction... -
Page 3: Introduction
2-wire cable. Ovanet is Nokeval’s second generation radio network, which uses Wirepas Connectivity technology and Nokeval’s own additions. The network uses 2.4-2.48 GHz band, which is available all over the world. The product names basically begin with the Ovazone prefix. -
Page 4: Installation
Antenna C module connector POL connector for configuration Illumination B module sensor connector RF1 LED RF2 LED SRV LED PWR LED ON/OFF switch Air pressure sensor (future option) Battery holder Temperature and humidity sensor External 5 V input A module connector USB connector Button... - Page 5 Open the case cover by pushing the top part of the case and pulling the cover away from the case. Connect a Nokeval DCS772 programming cable and a POL-3PIN adapter to your computer. Connect the POL-3PIN adapter to the J6 POL connector of the device. The polarity does not matter.
- Page 6 Menu chart Conf Temperature Temp Temp Humidity Humi Uncal1 Temp+Humi Barometer Barometer Cal1 Temp+Humi Period Uncal2 Cal2 Batt[V] Ovanet Batt[%] CalDate ExtPow Gain Barometer Switches Barometer Uncal1 Period Cal1 Sampling time Uncal2 Autocal Cal2 Autocal Period[h] Base level Ovanet Period Max adjust Module Time...
- Page 7 0x. Ovanet -> QoS This setting must not be touched unless Nokeval support tells you to do so. Ovanet -> Node address This shows the unique address of the device, same as in the label. The node address cannot be changed.
- Page 8 Mon -> ExtPow Is the external power connected. Mon -> Switches The ON/OFF switch and the button status for the manufacturer’s testing. Cal menu The calibration menu settings are only for the manufacturer use, and they are not explained in this manual.
-
Page 9: Usage
Usage Power up and shutdown If the device is not needed for a while, switch it off by sliding the ON/OFF switch to position 0. The device will not measure nor transmit measurement data anymore. The device is not participating the radio network which may affect the range of the other devices in the network. -
Page 10: Specifications
Specifications Environment Storage temperature -40...+70 °C without the battery, max 50 °C with the battery Operation temperature +5...+60 °C Operation humidity 5...95 %RH, non-condensing Protection class IP30 Enclosure material Plastic (PC+ABS) Compatibility Ovazone series devices and Ovaport service Measurements Weight About 370-390 g including the wall holder and a battery depending on the model Maximum dimensions Height 160 mm... - Page 11 The models (not all are available yet) Ovazone-Core-T-RH-LUX (basic model) Ovazone-Core-T-RH-BARO-LUX (air pressure sensor support added) Ovazone-Core-T-RH-LUX-CO2 (carbon dioxide concentration sensor added) Ovazone-Core-T-RH-LUX-CO2-VOC (volatile organic compound sensor added) Ovazone-Core-T-RH-LUX-CO2-VOC-UNI Ovazone-Core-T-RH-LUX-SERIAL-UNI Ovazone-Core-Router (repeater for expanding the radio network) Conformity EMC immunity...
-
Page 12: Warnings
Warnings The device must not be disposed of in household waste. Observe local regulations concerning the disposal of electrical waste. The device contains a battery. Manufacturer Nokeval Oy Rounionkatu 107 FI-37150 Nokia Finland Phone +358 3 342 4800 (Mon-Fri 8:30-16:00 EET) http://www.nokeval.com/...
Need help?
Do you have a question about the Ovazone-Core-T-RH-BARO-LUX and is the answer not in the manual?
Questions and answers