Table of Contents
Advertisement
Quick Links
Assembly instructions
00
UK HELP-LINE:
7/24h help service
Ph.+39-3351022019
Counterweighted / projecting up and
max.
h 2,15 m
over door*
*= need extra accessory
canopy arm part#992012 not included in
the kit
WA R N I N G :
Only to be installed on well balanced doors.
WA R N I N G :
Carefully read this mounting instruction before installation.
In case you should require further informations, contact the manu-
facturer :
24V belt driven Garage door opener
Sectional door
max.
h 2,15 m
Rév.1008 ENG
Standard door
max.
h 2,30 m
Kg
Max traction
force:
0 kg
max.
m
2
Power;
230 V/ 50 Hz
Gear
8-24 V dc
Opening time
11-18 sec.
MADE
IN ITALY
Min.
5 cm
Page 1
Advertisement
Table of Contents
Related Manuals for Ducati 8500SF
Summary of Contents for Ducati 8500SF
-
Page 1: Assembly Instructions
Assembly instructions Rév.1008 ENG 24V belt driven Garage door opener Max traction force: 0 kg max. Power; 230 V/ 50 Hz UK HELP-LINE: Gear 8-24 V dc Opening time 7/24h help service 11-18 sec. MADE Ph.+39-3351022019 IN ITALY Counterweighted / projecting up and Standard door Sectional door Min. - Page 2 Index CHAPTER CONTENTS PAGE WARNING Kit contents Technical specifications Garage door types Standard non projecting up-and-over door Sectional door Projecting up-and-over door Operating limits & Installation Scheme Assembly instructions 10-12 Fixing instructions 13-14 Manual release 230V power supply Remote control coding Power adjustment Electronic board CTH29S Setting the travel limits...
-
Page 3: Warning
Very Important Safety WARNINGS This garage door opener has been designed and tested to offer safe service provided it is installed, ope- rated, mantained and tested in strict accordance with the instructions and warnings contained in this manual. Please, carefully reat this instruction manual before to procede with installation of your garage door ope- ner, and make sure that weight , dimension and type of your garage door are within the limits of your garage door opener model. - Page 4 Never permit anyone to cross path of closing garage door. No one should go under a stopped, partially opened garage door. Always make sure to have connected the unlocking cable in order to permit to manually unlock ( from inside and outside) the garage door and operate it manually in case of power failure or other problem.
-
Page 5: Kit Contents
1. kit contents 8500SF Complete gear 24V d.c with electronic board CTR29S, receiver and transformer One rolling code , 2 channels radio transmittent 433,92 Mhz Belt drive 270 cm “U” iron rail (3 x. 90cm) with 2 connectors Manual unlocking device from inside/outside... -
Page 6: Garage Door Types
3. Garage door types Draw.2 3.1 Non projecting up-and-over door For the installation on a non projecting up-and- over door, no extra accessories are needed. Use the 2 standard door bra- kets to connect the trolley to trolley the door. standard door brakets 3.2 Sectional door... -
Page 7: Operating Limits & Installation Scheme
4. Operating limits & Installation scheme To fix the rail of the garage door opener, a minimal distance of 5 cm is needed between ceiling and door. And a minimal distance of 1cm is needed between rail and door ( see draw.6) Rack containing the chain drive system Draw.5 Power 230V - 50/60Hz... -
Page 8: Wall Mount
Installation scheme Draw.7 Wall mount (this zone must be strong and reinforced with an iron plate if needed) Page 8... - Page 9 Gear support The gear box must extra support for rail be fixed to the ceiling with the sup- the rail pieces “830” can be additio- plied parts “821” nally fixed to the ceiling with a cable Door mount (this zone must be strong and reinforced with an iron plate if needed) CAUTION:...
-
Page 10: Assembly Instructions
5. Assembly instructions 1° step: “U” Rail assembly Assemble the 3 elements of the rail (part # 829) by fitting them into the 2 rail braces (part # 830). See draw.8-10. Draw.8 Draw.9 Draw.10 2° step: fixing the belt into the trolley and around the pulley The pulley and the trolley are supplyed pre-assembled: Draw.11 Trolley... - Page 11 Slide the belt through the trolley as showned on draw.12 and then pass it around the pulley. Lock the belt with the securing plate as showed on draw.13-14 WARNING: The securing plate must connect the belt in a specific position: on the side opposite to the unlocking plug fixed on the trolley, and between the trolley and the pulley.
- Page 12 4° step: connect the belt to the pulley on the motor plate turn the motor head, and take off the pulley cover. Slide the belt around the pulley ( draw.17). Put the pulley cover on and fix it with the screws ( draw.18). Insert the “U”...
-
Page 13: Fixing Instructions
6. Fixing instructions 5° step: Door Jamb Mount: Position the pilot holes horizontally on the vertical centre line of the door. Fasten the bracket 828 to the door jamb or wall by means of 2 bolts (not supplied) of the right size and type of the structure. - Page 14 7° step: Door fixing Close the garage door. The fixing plate 809 is supplyed pre-assembled to the trolley by 2 brakets. These brackets are supplied for installation on a STANDARD NON PROJECTING-UP-AND-OVER DOOR 1°) Push left the unloking handle to release and manually moove the trolley ( draw.28) 2°) Slide the trolley to the front and advance the brackets to find the right fixing position of the plate 809.
-
Page 15: Manual Release
WARNING: trolley Draw.32/ B for installation on a standard door braket projecting up-and-over door, an extra canopy arm (not supplied inside the kit) is needed to connect the trolley to the door) as in draw. 32/B. Please see also page 6 point 3.3. Please refear to the specific intruction manuals sup- plied with the canopy arm to be separately purchased. -
Page 16: V Power Supply
Draw.38 Wrap connection to manually unlock from inside and outsi- de the door. Connect the cable to the handle.Turn the handle to unlock. Draw.37 wrap compressor door handle 8. 230V power supply wiring Lift the motor cover (draw.39-40) Connect the 230 V 50/60 Hz input cable to the transformer terminal board (draw.41-42-43). A fuse is mounted on the transformer to protect low voltage system (draw.42). -
Page 17: Remote Control Coding
9. Remote control coding (6203 rolling code) Rolling code remote ref. 6203/ rolling transmitts a unique “rolling code” (billions of continuously changing combinations) on a frequency of 433 MHz. With 2 buttons, has 2 channels of transmission. 1° channel = pushing on “ON “ button 2°... -
Page 18: Electronic Board Cth29S
11. Electronic Board CTH29S Draw.46 POWER TIME halogen lamp 20V 24W sec. To travel limits To transformer To motor Garden courtesy light push button to memorize or dela- 24V 10W max. te remote controls code LED= red light LED as indications for memorizing or delating remote control Blinker codes... -
Page 19: Setting The Travel Limits
12. Setting the travel limits Warning: to operate setting of travel limits you must check that: the electronic panel must be on step-by step operating function = “TIME” Trimmer must be completely rotated clockwise. See page 20; Travel limits regulates the points at which the door will stop each operation when moving up or down. The 2 limits flags red and green will stop the door movement when they get in correspondance of thelli- mit switch . -
Page 20: Automatic Closing
13. Automatic closing Operate adjustments and settings only with garage door in closed position, and make sure any object child or person will be in the operating zone To activate the door automatic closing programme, rotate the “TIME” trimmer anti-clockwise from 0 posi- tion, until the desired time pause interval is reached. -
Page 21: Warranty & After Sale Service
16.Warranty & After sale service DUCATI products are guaranteed for 24 months from purchase date, for manufacture or material defects. In case of repair, the product shall be returned to the to one of our authorised after-sale centres. The authorised technical assistance centres are the only acknowledged suitable to carry out repairs under guarantee. -
Page 22: Declaration Of Conformity
19. CE declaration DECLARATION OF CONFORMITY DUCATI HOME AUTOMATION Automazione Cancelli Via Cassani, snc 43036 Fidenza (PR) ITALY declare under our sole responsabilità that the products listed below to witch this declaration relates: UP100 Garage Door Opener when installed, used and mantained according to all the manufacturer instructions on a garage door...