Advertisement
Quick Links
Safety Information
WARNING: Improper use of this product or failure to follow
these instructions may result in equipment damage, personal
injury, or death. Read and understand all instructions for proper
installation and use of this product.
WARNING: Before loading equipment in the cabinet, be sure all
parts and hardware are properly installed and tightened.
Intended Use
Install RMR Wall-Mount Enclosures only in indoor, nonhazardous locations
such as manufacturing environments and warehouse distribution centers.
The enclosures are rated for NEMA Type 12 and IP 55 protection, which
provides protection against dirt and dust, light spray with nonc orrosive liquid
and penetration from oil seepage. Use indoors only; do not use outdoors.
Use RMR Wall-Mount Enclosures for information technology and
telecommunications equipment, systems control automation electronics
and/or instrumentation. Allow only qualified service personnel to use this RMR
Wall-Mount Enclosure.
Installation Instructions
RMR WALL-MOUNT ENCLOSURES
IIS-737100, 09/16/16, Rev. 1, CPI/SJG
800-834-4969 (USA & Canada) • www.chatsworth.com • techsupport@chatsworth.com
For international phone numbers, see our website or contact CPI Tech Support.
This drawing contains proprietary and confidential information and is protected by U.S. and international law. Unauthorized reproduction, disclosure or use of the drawing
or the information therein is expressly forbidden except as agreed to in writing by Chatsworth Products, Inc.
RMR Fixed Wall-Mount
(A2 Model)
RMR Swing Wall-Mount
(A3 Model)
Page 1 of 8
Advertisement
Summary of Contents for Chatsworth Products A2
- Page 1 This drawing contains proprietary and confidential information and is protected by U.S. and international law. Unauthorized reproduction, disclosure or use of the drawing or the information therein is expressly forbidden except as agreed to in writing by Chatsworth Products, Inc.
- Page 2 Included Hardware (6) Sealing Washer (6) M8x40 Lag Screw Note: For A2 model RMR Fixed Wall-Mount - Start on step 2. Skip these steps and jump to “Assembly Sequence – Equipment Rails” (page 4) if using RMR Quick Wall- Mounting Kit.
- Page 3 Installation Instructions RMR WALL-MOUNT ENCLOSURES Step 2: Mounting Rear Chassis to the wall 5. Determine desired location of cabinet on wall. 6. Place rear chassis flush against wall at desired location. 7. Use the rear chassis as a template and drill pilot holes for the two top corner lag screws.
- Page 4 Installation Instructions RMR WALL-MOUNT ENCLOSURES Assembly Sequence – Equipment Rails Round Head Bolt Tools Required M10 Socket Driver Step 1: Equipment Rail Adjustment 15. Loosen nut. Slide rail to new position, or remove hardware to locate to a different slot. 16.
- Page 5 Installation Instructions RMR WALL-MOUNT ENCLOSURES Assembly Sequence – Rear Back Plate Mounting Tools Required M13 Socket Driver Step 1: Rear Back Plate Mounting 1. Install plastic spacers over M8 studs in cabinet Plastic Spacer 2. Install back plane (arrow at top) onto M8 studs 3.
- Page 6 Installation Instructions RMR WALL-MOUNT ENCLOSURES Assembly Sequence – Adjustable Mounting Plate Tools Required M8 Nut M13 socket driver T25 Torx screw driver Mounting Step 1: Adjustable Mounting Plate Bracket 1. Insert tab on mounting bracket into square hole 2. Attach with two M5.5 Torx screws with star washer (Torque 44 IN-LB [5 N-M]).
- Page 7 Installation Instructions RMR WALL-MOUNT ENCLOSURES Assembly Sequence – Door Assembly and Bonding Tools Required T25 Torx screw driver Step 1: Door Bonding 1. Align hinges on door with hinges on cabinet. 2. Press hinge pins through door hinges until fully seated. (detent engaged) 3.
- Page 8 Installation Instructions RMR WALL-MOUNT ENCLOSURES Assembly Sequence – Center Chassis Bonding Tools Required T25 Torx screw driver Step 1: Door Bonding 1. Attach ground wire to circular hole using M5.5 Torx panhead screw (torque 44 IN-LB [5 N-M]). Attach Ground Wire to hole Page 8 of 8...